Results 151 to 160 of about 2,463,569 (223)

Integrating Grain to Ground Motion Data for Critical Rock Bridge and Slope Failure Analysis

International Journal for Numerical and Analytical Methods in Geomechanics, Volume 50, Issue 16, Page 5891-5918, November 2026.
ABSTRACT Rock masses can fail catastrophically with little warning, yet their stability depends on hidden internal connections that channel forces and localise damage. Among these, rock bridges–a “known unknown” in slope mechanics–lock fractured rock and control how failure unfolds, but their concealed geometry and uncertain strength obscure where and ...
Antoinette Tordesillas, Shuo Zhou, Leonnardo Probst, Pat Bellett, Michal Nitka, Jacek Tejchman   +5 more
wiley   +1 more source

Effects of Void Characteristics on the Mechanical Properties of Carbon Fiber Reinforced Polyetheretherketone Composites: Micromechanical Modeling and Analysis. [PDF]

Polymers (Basel)
Zhang Y, Li Y, Luan X, Meng B, Liu J, Lu Y.   +5 more
europepmc   +1 more source

Micromechanical Modeling of Damage Evolution and Mechanical Behaviors of CF/Al Composites under Transverse and Longitudinal Tensile Loadings. [PDF]

Materials (Basel), 2019
Wang Z, Yang S, Du Z, Jiang W, Zhang A, Cai C, Yang W.   +6 more
europepmc   +1 more source

Comparison of Mesoscale Crack Advance and Process Zone Element Approaches for Simulating Ductile Crack Trajectories in Steel

Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 11, Page 4850-4862, November 2026.
ABSTRACT Rigorous application of continuum damage mechanics (CDM) models coupled with crack propagation schemes can predict crack branching or zigzag trajectories near the crack tip, even when the macroscopic crack growth is straight. This arises from oscillations in the local damage field and is consistent with experimental observations of ductile ...
Andrew Ziccarelli, Amit Kanvinde, Gregory Deierlein   +2 more
wiley   +1 more source

Three-Dimensional Micromechanical Modeling of Martensite Particle Size Effects on the Deformation Behavior of Dual-Phase Steels. [PDF]

Materials (Basel)
Cavusoglu O, Toros S.
europepmc   +1 more source

Micromechanical Modeling of the Elasto-Viscoplastic Behavior and Incompatibility Stresses of β-Ti Alloys. [PDF]

Materials (Basel), 2018
Lhadi S, Chini MR, Richeton T, Gey N, Germain L, Berbenni S.   +5 more
europepmc   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, Volume 47, Issue 19, Page 17076-17090, 10 October 2026.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

Moisture Effects on the Dimensional Stability of Bistable Carbon/Epoxy Laminates

Polymer Composites, Volume 47, Issue 19, Page 17449-17460, 10 October 2026.
Experimental and numerical approach for studying moisture effects on composite dimensional stability. ABSTRACT Bistable composite laminates are attractive because they can switch between two stable shapes without continuous energy input, enabling applications in morphing structures and energy harvesting devices.
Andrea Dei Sommi, Francesca Lionetto, Francesco Nicassio, Alfonso Maffezzoli   +3 more
wiley   +1 more source

Accessing Colony Boundary Strengthening of Fully Lamellar TiAl Alloys via Micromechanical Modeling. [PDF]

Materials (Basel), 2017
Schnabel JE, Bargmann S.
europepmc   +1 more source

Prediction of Tensile Behavior in Additively Manufactured Polymer Matrix Composites via an Integrated Analytical Approach

Polymer Composites, Volume 47, Issue 19, Page 17501-17513, 10 October 2026.
Integrated analytical framework for tensile response of additively manufactured polymer composites, supported by experimental validation. ABSTRACT Additive manufacturing (AM) enables innovative product development through its material versatility and design freedom, further enhanced by advanced materials such as composites.
Ozgur Poyraz, Abas Abasov
wiley   +1 more source