Results 41 to 50 of about 14,841 (305)
Residual stress and microstructural characterization using Rietveld refinement of a carburized layer in a 5120 steel [PDF]
, 1995 Rietveld refinement of X-ray diffraction patterns has been used to provide microstructural information complementary to conventional X-ray residual stress measurements through a carburized layer containing a maximum vol.
Rangaswamy, Partha +4 more
core +1 more source
Microstructure Refinement of Structural Steel in China
ISIJ International, 2003 In Oct. 1998 Chinese government opened national program: Fundamental Research on New Generation of Iron and Steel Materials in China (N.G. Steels). The progress of on-going project has been briefly reported in this paper. In order to get microstructure refinement in structural steels, the following 5 ways have been studied: For Ferrite+Pearlite ...
openaire +2 more sources
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
BuildingsLarge quantities of agricultural waste, particularly rice husk ash (RHA), are generated worldwide each year, and the lack of rational, value-added disposal pathways poses both environmental and resource-utilization challenges.
Shuo Wang, Ming Sun
doaj +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
MetalsSpecimens from commercial and continuously cast A356 ingots have been friction stir-processed, and tensile deformation has been characterized. These two types of ingots have been found to be damaged in the liquid state, but at different levels.
Murat Tiryakioğlu +2 more
doaj +1 more source
The effect of the austenite grain refinement on the tensile and impact properties of cast Hadfield steel [PDF]
Materials Research, 2018 This paper studied the effect of the austenite grain refinement on the tensile and impact properties of a cast Hadfield steel (12 % Mn, 1.2 %C and 0.65 % Si). The austenite grain refinement was obtained by hafnium inoculation.
Bianka Nani Venturelli +2 more
doaj +2 more sources
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Small-angle neutron scattering investigations of nanocrystalline alloy chips obtained by machining
Cogent Engineering, 2014 Ultrafine-grained (UFG) materials exhibit significantly enhanced mechanical properties. This has brought renewed attention on the use of large strain or severe plastic deformation as a means for achieving microstructural refinement in metals and alloys ...
Elwyn Rebello +7 more
doaj +1 more source
Residual stress characterization in friction stir welds of alloy 625
Journal of Materials Research and Technology, 2019 Alloy 625 (UNS N06625) welded sheets were evaluated in the present study. Friction stir welding (FSW) was performed in a range of tool rotational speed from 1200 to 200 rpm, welding speed from 1.0 to 1.5 mm/s and constant axial force.
Guilherme Vieira Braga Lemos +6 more
doaj +1 more source