Results 61 to 70 of about 2,043 (264)
Advanced Engineering Materials, EarlyView.Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath +2 more
wiley +1 more source
A Review of Mid-Infrared Supercontinuum Generation in Chalcogenide Glass Fibers
Applied Sciences, 2018 Chalcogenide glasses have the advantages of a wide transparency window (over 20 μm) and high optical nonlinearity (up to a thousand times greater than that of silica glasses), making them good candidates for mid-infrared supercontinuum generation.
Shixun Dai +5 more
doaj +1 more source
Micromachines, 2020 In this paper, a pentagonal microstructured optical fiber polarization filter by utilizing a surface plasmon resonance effect is proposed. The characteristics of the mode-coupling and filtering of the filter are studied by making use of the full-vector ...
Chao Wang +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids
Advanced Functional Materials, EarlyView.This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow +9 more
wiley +1 more source
Laser‐Induced Graphene from Waste Almond Shells
Advanced Functional Materials, EarlyView.Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A soft, dual‐channel hydrogel patch enables simultaneous detection of wound temperature and strain by integrating ion‐diffusion‐mediated thermoelectric and resistive sensing. The conformal design maintains stable performance during motion, capturing subtle inflammatory and mechanical changes for continuous wound monitoring.
Yu Fang +7 more
wiley +1 more source
IEEE Photonics Journal, 2018 Cascaded cross-phase modulation instability (XPMI) is experimentally observed in the normal dispersion regime of a birefringent tellurite microstructured optical fiber (BTMOF).
Tonglei Cheng +3 more
doaj +1 more source
Microstructured optical fibers: where�??s the edge?
Optics Express, 2002 We establish that Microstructured Optical Fibers (MOFs) have a fundamental mode cutoff, marking the transition between modal confinement and non-confinement, and give insight into the nature of this transition through two asymptotic models that provide a mapping to conventional fibers.
Kuhlmey, B. T. +5 more
openaire +3 more sources
Advanced Functional Materials, EarlyView.A swelling‐programmed micropatterned hydrogel guides adherent cells through a controlled transition from cell–matrix anchoring to cadherin‐mediated cell–cell compaction, enabling rapid assembly of high‐viability spheroids with defined size and morphology.
Han Gyeol Nam +8 more
wiley +1 more source