Results 91 to 100 of about 4,655 (257)

Encyclopedia of 2D β′‐In2Se3 Growth Using Chemical Vapor Deposition: The Effects of Synthesis Parameters Onto Material Quality

Advanced Engineering Materials, EarlyView.
A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge, P. Sanju S. Panawala, Joseph F. S. Fernando, Zhenhuan Chen, Chao Zhang, Dong‐Chen Qi, Liangzhi Kou, Konstantin L. Firestein, Dmitri V. Golberg   +8 more
wiley   +1 more source

Improving the storage quality and suppressing off-flavor generation of winter jujube by precise micro-perforated MAP

Frontiers in Plant Science
IntroductionTraditional modified atmosphere packaging (MAP) cannot meet the preservation requirements of winter jujube, and the high respiration rate characteristics of winter jujube will produce an atmosphere component with high CO2 concentration in ...
Xinzhi Cui, Yibing Ding, Chanchan Sun, Xiulian Li, Shuzhi Yuan, Fengjun Guo, Xiangquan Zeng, Xinguang Fan, Shuyang Sun   +8 more
doaj   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Biogenic Amine Content and Shelf-Life of Salmon Fillets Packaged in Modified Atmospheres of Low-Level Carbon Monoxide and Different Carbon Dioxide Concentrations

Polish Journal of Food and Nutrition Sciences
The objective of this study was to determine the biogenic amine levels and quality parameters of Atlantic salmon fillets packaged with a low level of carbon monoxide and varied concentrations of carbon dioxide and stored at 1°C. For this purpose, ambient
Esra Akkaya, Hilal Colak, Hamparsun Hampikyan, Ayse S. Engin, Enver B. Bingol   +4 more
doaj   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Effects of Compound Spice Essential Oil Combined with Modified Atmosphere Packaging on Protein Oxidation and Volatile Flavor Compounds in Sanhuang Chicken during Cold Storage

Shipin gongye ke-ji
To investigate the effects of compound spice essential oils from rosemary and cinnamon combined with modified atmosphere packaging (MEP) on myofibrillar protein oxidation and volatile flavor compounds in Sanhuang chicken during refrigeration (4 ℃，1~10 d).
Xue LI, Cailing LIU, Guangxian LIU, Li WANG, Bo DONG, Yao ZHANG, Dongwen FU, Jinqing HUANG   +7 more
doaj   +1 more source