Results 71 to 80 of about 383,783 (352)
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Evaluation of moisture damage for warm mix asphalt (WMA) containing reclaimed asphalt pavement (RAP)
Open EngineeringWarm mix asphalt (WMA) has attracted a lot of interest and attention from the pavement industry since it was introduced as a potential solution to replace traditional hot mix asphalt (HMA).
Mossa Zaineb +4 more
doaj +1 more source
TecnoLógicas, 2015 The influence of compaction temperature on the mechanical resistance and susceptibility to water of a bound granular material with asphalt cement (called MGEA) was evaluated in laboratory.
Hugo A. Rondón-Quintana +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani +2 more
wiley +1 more source
Nanoscale Quantification of Moisture Susceptibility of Paving Asphalts [PDF]
MATEC Web of Conferences, 2019 Moisture-induced damage due to stripping is one of the major concerns to the highway agencies in recent years. In this study, nanoscopic investigations were carried out to examine the effects of moisture in asphalt binders.
Roy Sumon, Hossain Zahid
doaj +1 more source
Advanced Engineering Materials, EarlyView.Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente +3 more
wiley +1 more source
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Influence of Coarse Aggregate Geometry and Mineral Composition on the Durability of Asphalt Concrete
InfrastructuresThe durability of asphalt concrete is highly dependent on the geometry and mineralogy of coarse aggregates, yet their combined influence on mechanical and moisture resistance properties is still not fully understood.
Hussein K. Mohammad +2 more
doaj +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Extent of moisture and mould damage in structures of public buildings
Case Studies in Construction Materials, 2017 The study concentrated on the extent of moisture and mould damage in different structures in 25 public buildings in Finland. Users of all the buildings had health symptoms suspected to be the result of moisture and mould damage, which is why moisture ...
Petri J. Annila +5 more
doaj +1 more source