Results 71 to 80 of about 6,930,042 (388)

Modeling the Drying Kinetics of Green Bell Pepper in a Heat Pump Assisted Fluidized Bed Dryer [PDF]

, 2016
In this research, green bell pepper was dried in a pilot plant fluidized bed dryer equipped with a heat pump humidifier using three temperatures of 40, 50 and 60C and two airflow velocities of 2 and 3m/s in constant air moisture.
Dehnad, D., Ganje, M., Ghanbari, V., Jafari, S.M.   +3 more
core  

Evidence of hydrological control of Sr behavior in stream water (Strengbach catchment, Vosges mountains, France) [PDF]

, 2002
Strontium and particularly 87Sr/86Sr ratios in stream water have often been used to calculate weathering rates in catchments. Nevertheless, in the literature, discharge variation effects on the geochemical behavior of Sr are often omitted or considered ...
Amiotte-Suchet, Anne Probst, Aubert, Bailey, Bain, Bain, Bonhomme, Clow, Dambrine, Daniel Viville, Depaolo, Dominique Aubert, Elias, Fichter, Fichter, Gosz, Gosz, Graustein, Graustein, Idir, Jacks, Krishnaswami, Ladouche, Land, Lasaga, Lefèvre, Likens, McNutt, Miller, Négrel, Négrel, Palmer, Peter Stille, Pionke, Pionke, Probst, Probst, Probst, Probst, Probst, Probst, Rice, Riotte, Stottlemyer, Tricca, Åberg, Åberg, Åberg, Åberg   +48 more
core   +2 more sources

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Optimisation of loading capacity of smoking kiln on drying characteristics of Catfish (Clarias gariepinus)

Agricultura Tropica et Subtropica, 2019
Fish smoking is widely used in the fish processing industry, especially in the post-harvest catfish product due to its simple operating technique. The objective of this study was to optimise the tray loading capacity of a smoking kiln for catfish.
Oduntan Oluwafemi Babatunde, Ajani Emmanuel Kolawole, Omitoyin Bamidele Oluwarotimi   +2 more
doaj   +1 more source

Investigation on drying kinetics analysis of gooseberry slices dried under open sun

Environmental Challenges, 2023
An experimental analysis of the drying behaviour of gooseberry slices dried in the open sun is described in this article. Gooseberries brought from the local market were cut approximately semi-circular in cross-section, with an average length of 20–25 mm
Vijay Patel, K.B. Judal, Hitesh Panchal, Bharat Singh, Amit Jomde, Abhinav Kumar, Anand Patel, Rupal Jain, Kishor Kumar Sadasivuni   +8 more
doaj   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Understanding the friction mechanisms between the human finger and flat contacting surfaces in moist conditions

, 2010
Human hands sweat in different circumstances and the presence of sweat can alter the friction between the hand and contacting surface. It is, therefore, important to understand how hand moisture varies between people, during different activities and the ...
Carre, M.J., Lewis, R., Liu, X., Texier, C., Tomlinson, S.E.   +4 more
core   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Effects of Silvopasture Establishment on Aqueous and Gaseous Soil N Losses at the University of New Hampshire Organic Dairy Research Farm [PDF]

, 2017
The expansion of local agriculture in the New England region is putting increased pressure on farmers to expand their arable land base. While clear-cutting is a traditional method of converting forested land to agriculture, it is known for having ...
Slebodnik, Kathryn Ann
core   +1 more source

Laser Metal Deposition of Aluminum Alloys 7075 and 5083 with the Addition of Volatile Alloying Elements through Powder Blending

Advanced Engineering Materials, EarlyView.
This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen, Anastasiya Toenjes, Annika Bohlen, Thomas Seefeld   +3 more
wiley   +1 more source