Results 71 to 80 of about 16,101 (266)

On Floating-Based System’s Center of Mass Shifting for Physical Interaction: A Case Study in Aerial Robotics

Aerospace
Floating-base robotic systems rely critically on their inertial geometry to maintain stability and regulate interaction forces in the absence of fixed ground constraints.
Matteo Fumagalli
doaj   +1 more source

Experimental Research of Continuous Concrete Beams with GFRP Reinforcement

Advances in Civil Engineering, 2018
Continuous beams are often used within RC structures, which are exposed to aggressive environmental impact. The use of the fiber-reinforced polymer (FRP) reinforcement in these objects and environments has a big significance, taking into account tendency
Nikola Baša, Mladen Ulićević, Radomir Zejak   +2 more
doaj   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Plastic Properties of Prestressed High-Strength Steel Reinforced Concrete Continuous Beams

Applied Sciences
In this paper, the plastic properties of prestressed high-strength steel reinforced concrete (PHSSRC) beams are studied, by performing static load tests on eight built-in Q460 and Q690 prestressed high-strength steel reinforced concrete continuous beams ...
Jun Wang, Wendong Yang
doaj   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

A Computational Framework for Load-Constrained Human Squat Motion with Nonlinear Joint Modeling

Applied Sciences
Human squat motion is commonly analyzed using inverse dynamics, where joint moments are computed from experimentally measured kinematics. Such analyses typically assume that the observed motion is mechanically feasible and do not explicitly account for ...
Karol Nowak, Anna Szymczak-Graczyk, Aram Cornaggia, Tomasz Garbowski   +3 more
doaj   +1 more source

Ontology‐Aligned Structuring and Reuse of Multimodal Materials Data and Workflows Toward Automatic Reproduction

Advanced Engineering Materials, EarlyView.
Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari, Abril Azocar Guzman, Sarath Menon, Stefan Sandfeld, Tilmann Hickel, Markus Stricker   +5 more
wiley   +1 more source

The Management of Regional Biodiversity – Forest Potential [PDF]

Revista de Management Comparat International, 2011
The considerations on the ability of forest to maintain ecological balance and numerous environmental protection functions require the exercise of a sensible management, consistent with regional development plans.
Mariana BRAN, Claudia Elena PAICU , Iuliana DOBRE   +2 more
doaj  

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source