Results 201 to 210 of about 168,922 (233)
Some of the next articles are maybe not open access.
Synthesis of zirconia monoliths for chromatographic separations
Journal of Chromatography A, 2006The aim of this work is to join the advantages of two different kinds of stationary phases: monolithic columns and zirconia-based supports. On the one hand, silica monolithic columns allow a higher efficiency with a lower back-pressure than traditional packed columns.
Jérôme, Randon +5 more
openaire +2 more sources
Mechanical and Surface Properties of Monolithic Zirconia
Operative Dentistry, 2018SUMMARYPurpose:This study compared monolithic zirconia with conventional ones based on mean roughness (Ra), Vickers hardness (VHN), topography, transmittance, grain size, flexural strength (FS), Weibull modulus, and fractographic behavior.Methods and Materials:One monolithic (Prettau Zircon [PR group]) and two conventional (ICE Zirkon Transluzent [IZ ...
Candido, L. M. +4 more
openaire +3 more sources
Two-Body Wear of Monolithic, Veneered and Glazed Zirconia and Their Corresponding Enamel Antagonists [PDF]
Objective. This study tested whether the two-body wear of monolithic zirconia and their corresponding enamel antagonists was higher compared to monolithic alloy and veneered zirconia. Materials and methods.
Malgorzata Roos +2 more
exaly +2 more sources
Clinical Fit of Monolithic Zirconia Single Crowns
The International Journal of Prosthodontics, 2018To analyze the clinical fit of monolithic zirconia single crowns (MZSCs) in a prospective cohort study.A total of 30 posterior teeth were restored with MZSCs. Silicone replicas were made to measure the clinical fit using a stereomicroscope. Measurements were conducted at 17 points per crown at the marginal and occlusal surfaces.The mean clinical fit ...
Stefanie Anke, Rau +4 more
openaire +2 more sources
Zirconia supported LaMnO3 monoliths for the catalytic combustion of methane
Applied Catalysis B: Environmental, 2002Abstract Novel LaMnO3 perovskite-based structured catalysts have been studied for methane catalytic combustion under lean, pre-mixed conditions. Monoliths have been prepared by wash-coating cordierite honeycomb substrates with lanthanum stabilised ZrO2, on which the perovskite was dispersed by either impregnation or deposition–precipitation (DP ...
Cimino S, Pirone R, Lisi L
openaire +5 more sources
Cement Choice and the Fatigue Performance of Monolithic Zirconia Restorations
Operative Dentistry, 2022SUMMARY This study investigated the fatigue failure load of simplified monolithic yttria partially stabilized zirconia polycrystal restorations cemented to a dentin-like substrate using different luting systems. Disc-shaped ceramic (Zenostar T, 10 mm Ø × 0.7 mm thick) and dentin-like substrate (10 mm Ø × 2.8 mm thick) were produced and randomly
L F, Guilardi +5 more
openaire +2 more sources
Fatigue resistance of monolithic strength-gradient zirconia materials
Journal of the Mechanical Behavior of Biomedical Materials, 2021PURPOSE Evaluation of the effect of three different dynamic fatigue protocols on the fracture resistance of two monolithic strength-gradient zirconia materials. MATERIALS AND METHODS A total of 240 specimens (3 × 4 × 45 mm) was milled from two different layers (incisal and middle) of two types of strength-gradient zirconia blanks (IPS e.
Lisa Marie Schönhoff +4 more
openaire +2 more sources
Considerations and Concerns Regarding Monolithic Zirconia Restorations
International Journal of Periodontics & Restorative DentistryAfter over a decade of use, there are persistent misunderstandings about monolithic zirconia (MZ) with respect to its characteristics and appropriate management. This leads to errors in its application that can negatively affect not only the efficiency and predictability of clinical workflows but also the long-term outcome for the patient. This article
Clinton D, Stevens +4 more
openaire +2 more sources
The Journal of Prosthetic Dentistry, 2016
The effect of anatomic contour design in all or parts of zirconia crowns is uncertain regarding clinical reliability and survival rates.The purpose of this in vitro study was to compare the load at fracture of monolithic, anatomic contour zirconia crowns with bilayered crowns with and without a cervical zirconia collar.Thirty zirconia crowns were ...
Marit Øilo +2 more
openaire +2 more sources
The effect of anatomic contour design in all or parts of zirconia crowns is uncertain regarding clinical reliability and survival rates.The purpose of this in vitro study was to compare the load at fracture of monolithic, anatomic contour zirconia crowns with bilayered crowns with and without a cervical zirconia collar.Thirty zirconia crowns were ...
Marit Øilo +2 more
openaire +2 more sources
Effect of changes in sintering parameters on monolithic translucent zirconia
Dental Materials, 2014Aim of this study was to evaluate the effect of different sintering parameters on color reproduction, translucency and biaxial flexural strength of monolithic zirconia.Translucent zirconia discs having 15mm diameter, 1mm thickness, and shade A3 were milled and divided according to the sintering temperatures (1460°C, 1530°C, and 1600°C) into three ...
Kamal Ebeid +5 more
openaire +2 more sources

