Results 41 to 50 of about 2,079 (177)

Investigation of the Effect of Al₂O₃ Nanoparticle-Added MQL Lubricant on Sustainable and Clean Manufacturing

Lubricants
In this study, in order to improve the characteristics of the vegetable-based cutting fluids used in the MQL technique and increase the machining performance of MQL and its positive effects on sustainable manufacturing, the effects of the MQL method with
Fuat Kara
doaj   +1 more source

Experimental Evaluation of Turning AISI 304 Using Minimum Quantity Lubrication With Vegetable‐Based Green Cutting Fluids

MetalMat, Volume 3, Issue 1, March 2026.
This study experimentally evaluates the performance of eco‐friendly vegetable‐based cutting fluids—coconut, sunflower, and palm oils—during turning of AISI 304 stainless steel under minimum quantity lubrication. Palm oil exhibited superior lubrication and cooling characteristics, yielding the lowest cutting force, temperature, and surface roughness ...
Ranjith Ravindran Nair, Praveen Vijayan, Jayesh Shanthi Bhavan, Ajin C. Sajeevan   +3 more
wiley   +1 more source

A review on application of nanofluid MQL in machining [PDF]

AIP Conference Proceedings, 2017
Heat generation is an inevitable phenomenon during machining. To eradicate heat oriented detrimental effects like surface burning, tool wear and so on-different types of cooling system are being used. Traditional flood cooling method is the most widely used technique; however the consumption rate of coolant is very high.
Mustafa Rifat, Md. Habibor Rahman, Debashish Das   +2 more
openaire   +1 more source

Helical Feed Milling with MQL for Boring of Aluminum Alloy

Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2008
MQL is applied to the helical feed milling hole-making process of aluminum alloy. It is difficult to drill on aluminum alloy without cutting fluid because the adhesion to the tool leads to a chip jam, the tool breakage or low accuracy.
Hiroyuki SASAHARA, Makoto KAWASAKI, Masaomi TSUTSUMI   +2 more
doaj   +1 more source

Valorization of Pretreated Salvinia molesta Biomass for Ciprofloxacin Biosorption: Kinetic Performance, pH‐Dependent Mechanisms, and Circular Economy Implications

Water Environment Research, Volume 98, Issue 2, February 2026.
Powdered Salvinia molesta biomass efficiently removed ciprofloxacin under environmentally relevant conditions, with optimal sorption at a near‐neutral pH. This study highlights invasive plant biomass valorization as a low‐cost circular solution for decentralized water treatment.
Leticia Yoshie Kochi, Raul Victor Santana Rios, Raizza Zorman Marques, Lia Sumie Nakao, Marcelo Pedrosa Gomes   +4 more
wiley   +1 more source

Application of MQL technique using TiO2 nanoparticles compared to MQL simultaneous to the grinding wheel cleaning jet

The International Journal of Advanced Manufacturing Technology, 2019
The minimum quantity lubrication + nanofluid technique has proven to be feasible in machining processes, since it has shown potential for improvements through its lubri-refrigeration and heat removal characteristics, beyond increase the surface quality workpiece surface, while minimizing diametrical wheel wear.
José Claudio Lopes, Mateus Vinicius Garcia, Roberta Silveira Volpato, Hamilton José de Mello, Fernando Sabino Fonteque Ribeiro, Luiz Eduardo de Angelo Sanchez, Kleper de Oliveira Rocha, Luiz Daré Neto, Paulo Roberto Aguiar, Eduardo Carlos Bianchi   +9 more
openaire   +2 more sources

Modulating Electronic Properties of N‐Heterocyclic Carbene Ligands: Effects on the Pd‐Catalyzed Buchwald–Hartwig Amination

European Journal of Inorganic Chemistry, Volume 29, Issue 2, January 12, 2026.
Pd complexes with electronically modified NHCs (NHC = N‐heterocyclic carbene) were analyzed in the Buchwald–Hartwig Amination under both strongly and weakly basic conditions. Investigations into the steric and electronic properties of the ligands are detailed.
Meilin Q. Lim, Cassandra DeFrancesco, Kasandra J. Brick, Sterling Renzoni, Eric Fortin Constant, Alexander A. Glover, Casey A. Lenart, Jesse LeBlanc, Charley Garrard, Eric C. Keske   +9 more
wiley   +1 more source

Surface Roughness Analysis in Machining of Stainless Steel by Trochoidal Milling under Dry and MQL Cutting Environment

Gazi Üniversitesi Fen Bilimleri Dergisi
Trochoidal milling is a machining technique that enables high-efficiency machining of particularly hard-to-cut materials using a specific tool path at high feed and cutting speeds.
Tuğçenur Özcan, Mustafa Günay
doaj   +1 more source

Effect of quantity in oil-water combined mist in high speed milling of Ti-6Al-4V

Nihon Kikai Gakkai ronbunshu, 2020
In this study, Ti-6Al-4V alloy was machined at high cutting speed of 200 m/min, and the tool wear progress and the cutting mechanics were experimentally investigated in order to clarify an effective cooling method.
Junsuke FUJIWARA, Takaaki ARIMOTO, Tetsuya TASHIRO   +2 more
doaj   +1 more source

Sustainable Prediction of Tool Life in Metal Cutting Processes Using Empirical and Mathematical Modeling Approaches

Advances in Materials Science and Engineering, Volume 2026, Issue 1, 2026.
Tool‐life prediction plays a vital role in improving machining efficiency, reducing production cost, and promoting sustainable manufacturing in metal cutting processes. This study presents an empirical and mathematical modeling approach for predicting tool life based on flank wear behavior under varying machining conditions.
Nagaraj P. B., Gururaj Lalagi, Lokesha K., Mallikarjuna Veerabhadrappa Bidari, Rajesh K., Jibitesh Kumar Panda, Mohammad Rezwan Habib   +6 more
wiley   +1 more source