Results 31 to 40 of about 3,663,734 (116)

Effect of Zn content and processing route on the microstructure, mechanical properties, and bio-degradation of Mg–Zn alloys

Journal of Materials Research and Technology, 2022
The effects of zinc content (2 and 4 wt%), heat treatment (solution-treated and T6), as well as hot deformation (extrusion and multi-directional forging (MDF)) on the microstructure, mechanical and degradation behavior of Mg–Zn alloys were studied.
Mohammad Asadollahi, Ehsan Gerashi, Reza Alizadeh, Reza Mahmudi   +3 more
doaj   +1 more source

A Study on the Influence of Zr on the Strengthening of the Al-10% Al₂O₃ Composite Obtained by Mechanical Alloying

Metals, 2023
Al2O3 is a traditional strengthening phase in aluminum matrix composites due to its high hardness and melting point. At the same time, zirconium is an important alloying element for heat-resistant aluminum alloys. However, its effect on the structure and
Alexey S. Prosviryakov, Andrey I. Bazlov, Alexander Yu. Churyumov, Anastasia V. Mikhaylovskaya   +3 more
doaj   +1 more source

Investigating the CO2 laser cutting parameters of MDF wood composite material [PDF]

, 2011
Laser cutting of medium density fibreboard (MDF) is a complicated process and the selection of the process parameters combinations is essential to get the highest quality of the cut section.
Olabi, Abdul-Ghani, A.G. Olabi, Eltawahni, Hayat, K.Y. Benyounis, H.A. Eltawahni, Benyounis, Khaled   +5 more
core   +2 more sources

Numerical simulation and experimental investigation on multi-directional forging of pure molybdenum [PDF]

, 2021
The multi-directional forging process of pure molybdenum was numerically simulated by using DEFORM-3D finite element simulation software. Based on the forging experiment, the effects of deformation temperature, forging reduction, and forging steps on the
DUAN Bo-hua, YANG Dong-lin, WANG De-zhi
core   +1 more source

On the solution treatment of severely deformed AA2024-O and subsequent natural aging

Journal of Materials Research and Technology, 2022
In this research, the effect of applying severe strain before solid solution treatment (SST) for AA2024-O was studied. Providing concurrent insights into solutionizing behavior and microstructural evolution corresponding to hardness is important.
Milad Forouzesh, Mohsen Kazeminezhad
doaj   +1 more source

Microstructure, Texture Evolution, and Mechanical Properties of MDFed GWZ Alloy Containing LPSO Phases on the Condition of High and Low Temperature Cycle Deformation

Metals, 2020
The current work systematically investigated the microstructure, texture evolution, and mechanical properties of MDFed Mg-13Gd-4Y-2Zn-0.5Zr (wt%) alloy (GWZ) on the condition of high and low temperature cycle deformation.
Beibei Dong, Zhimin Zhang, Xin Che, Jianmin Yu, Mu Meng, Jinlu Zhang   +5 more
doaj   +1 more source

Synergistic enhancement of strength and toughness of β-Ti alloy with a fine grain: Effect of deformation temperature [PDF]

MATEC Web of Conferences
It is difficult for as-cast titanium alloys to achieve high strength and toughness due to the presence of coarse β grains. In this study, multi-directional forging (MDF) was employed to break down the coarse β grains into fine grains and the mechanism of
Li Yili, Fang Hongze, Sun Shichen, Yu Jichang, Chen Ruirun   +4 more
doaj   +1 more source

The Structural Refinement of Commercial‐Purity Copper Processed by Equal Channel Angular Pressing with Low Strain Amplitude

Advanced Engineering Materials, Volume 27, Issue 21, November 2025.
Equal channel angular pressing of commercial pure copper under low strain amplitude (≈0.48) induces concurrent continuous and localized discontinuous dynamic recrystallization, forming a duplex structure influenced by strain heterogeneity and recovery. Moderate hardening after 4–12 passes results from progressive high‐angle grain boundary formation via
Paula Cibely Alves Flausino, Nayara A. N. da Silva, Bárbara C. de Almeida, Taise M. Manhabosco, Elaine C. S. Corrêa, Maria T. P. Aguilar, Paulo R. Cetlin   +6 more
wiley   +1 more source

Evolution of the Second-Phase Particles and Their Effect on Tensile Fracture Behavior of 2219 Al-xCu Alloys

Metals, 2020
In this study, the continuous evolution of the second-phase particles across as-cast, homogenization, multi-directional forging (MDF), and solution-aging treatment and their effect on tensile fracture behavior of 2219 aluminum alloys with different Cu ...
Daofen Xu, Kanghua Chen, Yunqiang Chen, Songyi Chen   +3 more
doaj   +1 more source

Adaptive multi-channel MAC protocol for dense VANET with directional antennas [PDF]

, 2009
Directional antennas in Ad hoc networks offer more benefits than the traditional antennas with omni-directional mode. With directional antennas, it can increase the spatial reuse of the wireless channel.
Xie, Xu, Yang, Shaoshi, Lv, Tiejun, Benxiong Huang, Xu Xie, Shaoshi Yang, Tiejun Lv, Huang, Benxiong   +7 more
core   +1 more source