Results 11 to 20 of about 39,571 (304)
Journal of Materials Research and Technology, 2023 In this study, we compare the thermoelectric properties of coarse-grained n-type Bi2Te2.55Se0.45 alloy prepared by induction melting with the bulk-nanostructured prepared by ball milling and hot-pressing techniques.
Farah M. El-Makaty +3 more
doaj +1 more source
The surface nanostructures of titanium alloy regulate the proliferation of endothelial cells
AIMS Materials Science, 2014 To investigate the effect of surface nanostructures on the behaviors of human umbilical vein endothelial cells (HUVECs), surface nanostructured titanium alloy (Ti-3Zr2Sn-3Mo-25Nb, TLM) was fabricated by surface mechanical attrition treatment (SMAT ...
Min Lai +6 more
doaj +1 more source
Nanostructured crystallization of casting alloys
Litiyo i Metallurgiya (FOUNDRY PRODUCTION AND METALLURGY), 2022 Crystallization of casting alloys has been shown to be a nanostructured process. Microcrystals of phases in the temperature range of liquidus and solidus, during eutectic and peritectic reactions, are formed from nanocrystals of components A and B of alloys, their free atoms and atomic complexes.
E. I. Marukovich +2 more
openaire +2 more sources
Plan-View Preparation of TEM Specimens from Thin Films Using Adhesive Tape [PDF]
, 2011 A simple plan-view sample preparation technique for transmission electron microscopy (TEM) specimens is proposed for thin films by tearing-off the film with adhesive tape. The demand for very thin samples is highest for nanostructured materials where the
Czigány, Zsolt
core +1 more source
Oxidation resistance of the nanostructured YSZ coating on the IN-738 superalloy [PDF]
Journal of Ultrafine Grained and Nanostructured Materials, 2014 Conventional and nanostructured YSZ coatings were deposited on the IN-738 Ni super alloy by the atmospheric plasma spray technique. The oxidation was measured at 1100°C in an atmospheric electrical furnace.
Ahmad Keyvani +2 more
doaj +1 more source
Nanostructured high-strength alloys [PDF]
Science, 2017 Metallurgy Low-density magnesium alloys are a promising type of material for making lighter vehicles and improving fuel efficiency. One challenge for lightweighting is developing high-strength magnesium alloys. Wu et al. created a dual-phase magnesium thin film with near-ideal strength.
openaire +2 more sources
Journal of Asian Ceramic Societies, 2020 The aim of this research is the evaluation of the influence of TiN, CrN and TiN/CrN nanostructured coatings on corrosion resistance of nickel-chromium dental alloy in artificial saliva environment with two pH levels (3.0 and 6.5).
Nidhal Sahib Mansoor +3 more
doaj +1 more source
Effect of deposition current density and annealing temperature on the microstructure and magnetic properties of nanostructured Ni-Fe-W-Cu alloys [PDF]
Science of Sintering, 2019 Ni-Fe-W-Cu alloy powders were obtained by electrodeposition from an ammonium citrate bath at current densities ranging between 70 and 600 mA cm-2. As the deposition current density increased, the contents of Fe and W in the alloy increased, and ...
Spasojević Milica +5 more
doaj +1 more source
Synthesis, structure and properties of nickel-iron-tungsten alloy electrodeposits - Part II: Effect of microstructure on hardness, electrical and magnetic properties [PDF]
Science of Sintering, 2016 Nanostructured nickel-iron-tungsten alloys were produced by electrodeposition from an ammoniacal citrate bath. The tungsten content of the alloy ranged from 0.8 wt.% to 11 wt.%, and the crystal grain size of the FCC phase of the solid solution ...
Ćirović Nataša +5 more
doaj +1 more source
Effect of activated alloys on hydrogen discharge kinetics of MgH2 nanocrystals [PDF]
, 2007 This is the post-print version of the final paper published in Journal of Alloys and Compounds. The published article is available from the link below. Changes resulting from the publishing process, such as peer review, editing, corrections, structural ...
Bouaricha +19 more
core +2 more sources