Analysis of critical negative rake angle and friction characteristics in orthogonal cutting of AL1060 and T2 [PDF]
Science Progress, 2020 The stagnant region often appears in front of the tool cutting edge, which is caused by mechanical inlay and excessive pressing in plastic metal cutting with large negative rake angle tools at a low speed.
Yanchun Ding +4 more
doaj +6 more sources
Edge Effect Analysis on orthogonal cutting the Plastic Metal Material-C10100 with Negative Rake Angle Tool [PDF]
E3S Web of Conferences, 2020 With the rapid development of the precision grinding and micro-cutting technology, scholars have become more and more interested in the forming mechanism and related characteristics of the rounded-edge tool and the negative rake angle tool.
Ding Yanchun, Shi Guangfeng
doaj +2 more sources
Effects of cutting tool geometry on material removal of a gradient nanograined CoCrNi medium entropy alloy [PDF]
Beilstein Journal of NanotechnologyCoCrNi medium-entropy alloys (MEAs) have attracted extensive attention and research because of their superior mechanical properties, such as higher ductility, strength, and toughness. This study uses molecular dynamics (MD) simulations to investigate the
Yu-Sheng Lu +3 more
doaj +2 more sources
Study on the forming mechanism and evolutionary pattern of stagnant region in mechanical scratching [PDF]
Scientific ReportsIn this paper, a combination of theoretical modeling, finite element simulation, and experimental methods is employed to investigate the forming mechanism and evolutionary pattern of the stagnant region during mechanical scratching with a diamond wedge ...
Yanchun Ding +6 more
doaj +2 more sources
Application of TOPSIS for multi response optimization of Process Parameters in dry hard turning of AISI 52100 steel [PDF]
INCAS Bulletin, 2021 In the present work by employing the Technique for order of preference by similarity to ideal solution (TOPSIS) machining parameters optimization is performed with polycrystalline cubic boron nitride (PCBN) tools while AISI 52100 steel hard turning (HT).
P. UMAMAHESWARRAO +3 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 Laser assistance and the use of a diamond tool with a negative rake angle are promising methods for machining hard and brittle materials. In this paper, a cutting force model and a smoothed particle hydrodynamics (SPH) model were constructed to ...
Chuangting Lin +7 more
doaj +1 more source
Slip-line metal cutting model with negative rake angle [PDF]
Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2012 A small dead region is seen in front of the rake face of the tool during cutting with negative rake. The lack of knowledge about the stagnant region in the cutting with negative rake requires researching new models. In this work, cutting mechanism of the metal cutting with negative rake angle tools and the stagnation zone formation were studied.
Ozturk, Sabri, Altan, Erhan
openaire +5 more sources
Basics of automation of profiling of high-efficient inserts of the tool for thread machining [PDF]
STED Journal, 2020 Many modern threaded joints, especially in the oil and gas industry, must satisfy high requirements for steel mechanical properties of which they are made.
Oleh Onysko +4 more
doaj +1 more source
Study of a Methodology for Calculating Contact Stresses during Blade Processing of Structural Steel
Metals, 2023 The article presents data about the distribution of contact stresses on the rake surface of the cutter when turning steel (Fe-0.4 C-1Cr), which were obtained by the split cutter method.
Victor Kozlov +4 more
doaj +1 more source
Influence of the Rake Angle on Nanocutting of Fe Single Crystals: A Molecular-Dynamics Study
Crystals, 2020 Using molecular dynamics simulation, we study the cutting of an Fe single crystal using tools with various rake angles α . We focus on the (110)[001] cut system, since here, the crystal plasticity is governed by a simple mechanism for not too ...
Iyad Alabd Alhafez, Herbert M. Urbassek
doaj +1 more source