Results 141 to 150 of about 329,403 (304)

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Investigation of Thermo‐Chemical Processes in Commercial MgO‐C Refractory Bricks With and Without MgO‐C Recyclate at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm, Jana Hubálková, Christian Schimpf, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +6 more
wiley   +1 more source

Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio

Advanced Engineering Materials, EarlyView.
This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov, Matheus Roberto Bellé, Anton Yehorov, Julia Richter, Olena Volkova   +4 more
wiley   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Median nerve fascicle to posterior interosseous nerve transfer to restore finger extension. [PDF]

Surg Neurol Int
Staniszewski T, Buckley N, Lee BJ, Hanna A.   +3 more
europepmc   +1 more source