Results 41 to 50 of about 367,691 (306)
4D‐Printed Magneto‐Plasmonic Microrobots for Programmable Spatiotemporal De‐Icing
Advanced Functional Materials, EarlyView.A 4D‐printing strategy is introduced to achieve programmable de‐icing devices. By aligning gold–magnetite nanofillers within a photosensitive resin, the printed structures exhibit dual magnetic and plasmonic functionalities, enabling precise spatio‐temporal ice removal through thermoplasmonic effects.
Amélie Pérot +7 more
wiley +1 more source
Jixie qiangdu, 2022 Due to study the influence of interfacial slip on the bearing capacity of hydrostatic and hydrostatic ball bearings with small orifice throttling, the Reynolds equation of ball bearings considering interfacial slip was established based on the linear ...
ZHOU YiHao, SHEN JingFeng, CHEN YuFei
doaj
Lubricants, 2023 Due to the coupling of the damper journal with the elastic ring and oil film, the elastic ring squeeze film damper (ERSFD) shows better dynamic performance in comparison with the traditional squeeze film damper (SFD). Therefore, a novel rigid–elastic–oil
Yan Li, Haisheng Yang, Sier Deng
doaj +1 more source
Monitoring of lubricant film failure in a ball bearing using ultrasound [PDF]
, 2006 A lubricant-film monitoring system for a conventional deep groove ball bearing (type 6016, shaft diameter 80 mm, ball diameter 12.7 mm) is described. A high-firequency (50 MHz) ultrasonic transducer is mounted on the static outer raceway of the bearing ...
Anderson +21 more
core +1 more source
Plain bearing stresses due to forming and oil film pressure [PDF]
Journal of Physics: Conference Series, 2009 This paper describes a methodology for assessing critical stress ranges arising in automotive plain bearings during engine operations. An industry-produced and run simulation program provides information on oil film pressure and overall bearing deformation during accelerated performance tests.
Burke-Veliz, A. +5 more
openaire +1 more source
Advanced Functional Materials, EarlyView.We report a polymer‐chain insertion strategy to fabricate pore‐threaded MOF thin films with precisely tuned surface chemistry and wettability. Grafting n‐alkane chains into the pillared layer Cu2(bdc)2(dabco) MOF thin film's vertical nanochannels enhances water stability, and induces hydrophobicity and lubricant‐free, solid‐like slippery behavior ...
Angana Borbora +4 more
wiley +1 more source
Strategies for Loading and Releasing Peptide Therapeutics in Biodegradable Carriers
Advanced Functional Materials, EarlyView.A biodegradable carrier‐based peptide delivery system is a powerful treatment platform for diverse diseases, owing to its superior therapeutic efficacy and low toxicity. This review examines the conventional peptide‐loaded carrier fabrication process and its current limitations.
Wookyoung Jang, Ki Wan Bong
wiley +1 more source
Jixie qiangdu, 2022 Combined with the high pressure and high temperature working condition and the characteristics of tooth and sliding ring combined seal, the mathematical model of the rotating slip ring type combined seal is established based on the theory of ...
ZHANG Yi +6 more
doaj
Hydrodynamic modelling of hydrostatic magnesium extrusion [PDF]
, 2006 Wilson’s hydrodynamic model of the hydrostatic extrusion process is extended to meet the geometry found on residual billets. The transition from inlet\ud to work zone of the process is not considered sharp as in the model of Wilson but as a rounded edge,
Moodij, E. +2 more
core +2 more sources
The application of ultrasonic NDT techniques in tribology [PDF]
, 2005 The use of ultrasonic reflection is emerging as a technique for studying tribological contacts. Ultrasonic waves can be transmitted non-destructively through machine components and their behaviour at an interface describes the characteristics of that ...
Anderson W. +12 more
core +1 more source