Results 61 to 70 of about 523,009 (263)
Cupric Oxide Nanostructures from Plasma Surface Modification of Copper
Biomimetics, 2019 Taking inspiration from the hydrophilic and superhydrophilic properties observed from the nanostructures present on the leaves of plants such as Alocasia odora, Calathea zebrina, and Ruelia devosiana, we were able to synthesize cupric oxide (CuO ...
Hernando S. Salapare +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold +2 more
wiley +1 more source
Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines
Advanced Engineering Materials, EarlyView.Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl +4 more
wiley +1 more source
A Fiber Optic Catalytic Sensor for Neutral Atom Measurements in Oxygen Plasma
Sensors, 2012 The presented sensor for neutral oxygen atom measurement in oxygen plasma is a catalytic probe which uses fiber optics and infrared detection system to measure the gray body radiation of the catalyst.
Alenka Vesel +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Selenium was incorporated into a sol–gel‐derived bioactive glass to enable sustained therapeutic ion release. The selenium‐containing glass preserved bioactivity while selectively inducing cytotoxicity in osteosarcoma cells and maintaining osteoblastic viability.
Breno Rocha Barrioni +7 more
wiley +1 more source
Comparative studies of air-plasma and oxygen-plasma cutting
Izvestiya MGTU MAMI, 2014 Peculiarities of plasma cutting, its advantages and disadvantages are considered. There are considered technical capabilities used plasma installation and analyzed the results of the conducted research.
A. N Vasiliev +3 more
openaire +1 more source
IEEE Journal of the Electron Devices Society, 2018 We demonstrate the electrical performances of AlGaN/GaN metal-insulator-semiconductor-high electron mobility transistors (MIS-HEMTs) with high quality Al2O3 gate dielectric deposited by plasma enhanced atomic layer deposition using both H2O and remote O2
Huan-Chung Wang +8 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova +2 more
wiley +1 more source