Results 11 to 20 of about 948,334 (268)

Comprehensive Analysis of Microstructure and Hot Deformation Behavior of Al-Cu-Y-Mg-Cr-Zr-Ti-Fe-Si Alloy

open access: yesMetals, 2023
Low sensitivity to hot cracking is very important not only for casting but also for ingots of wrought alloys. Doping of Al-Cu-(Mg) alloys by eutectic forming elements provides an increasing resistance to hot cracking susceptibility, but it also leads to ...
Sayed M. Amer   +6 more
doaj   +1 more source

On the Question of the Complex Processing of Pyrite Cinders

open access: yesInorganics, 2023
A complex processing variant for pyrite cinders, i.e., the technogenic waste generated in the production of sulfuric acid, was proposed. This method provided preliminary chemical activation of the initial raw materials that comprised thermal treatment ...
Bagdaulet Kenzhaliyev   +5 more
doaj   +1 more source

Properties of the Cement, Slag and Fly Ash Mixture Composition Corresponding to CEM II/C-M and CEM VI

open access: yesMaterials Proceedings, 2023
In the study, cement mixtures containing granulated blast furnace slag (GBFS) and siliceous fly ash (SFA) were tested, including those corresponding to special cements according to the PN-B-19707: 2013 standard.
Ewelina Tkaczewska, Grzegorz Malata
doaj   +1 more source

Wet Ball Milling Applied to Production of Composites and Coatings Based on Ti, W, and Nb Carbides

open access: yesPowders, 2023
The paper demonstrates the potential of wet ball milling of metals for the synthesis of various carbides and carbohydrides. The work reports on multicomponent carbides formed in Ti-(Cu/Fe/Si)-C, W-Fe-C, and Nb-(Cu/Fe/Si/Al)-C systems, as well as ...
Marina Eryomina, Svetlana Lomayeva
doaj   +1 more source

Evolution of Phase Transformation on Microwave Dielectric Properties of BaSixO1+2x Ceramics and Their Temperature-Stable LTCC Materials

open access: yesCrystals, 2023
BaSixO1+2x (1.61 ≤ x ≤ 1.90) and LiF-doped BaSi1.63O4.26 ceramics were prepared by using a traditional solid-state method at the optimal sintering temperatures. The evolution of phase compositions of BaSixO1+2x (1.61 ≤ x ≤ 1.9) ceramics was revealed. The
Tailai Wen   +9 more
doaj   +1 more source

Berry Phase in a Composite System [PDF]

open access: yesPhysical Review Letters, 2004
The Berry phase in a composite system with only one subsystem being driven has been studied in this Letter. We choose two spin-$\frac 1 2 $ systems with spin-spin couplings as the composite system, one of the subsystems is driven by a time-dependent magnetic field. We show how the Berry phases depend on the coupling between the two subsystems, and what
Yi, Xue Xi   +2 more
openaire   +3 more sources

BaTiO3/NixZn1−xFe2O4 (x = 0, 0.5, 1) Composites Synthesized by Thermal Decomposition: Magnetic, Dielectric and Ferroelectric Properties

open access: yesInorganics, 2023
To investigate the influence of spinel structure and sintering temperature on the functional properties of BaTiO3/NixZn1−xFe2O4 (x = 0, 0.5, 1), NiFe2O4, ZnFe2O4, and Ni0.5Zn0.5Fe2O4 were in situ prepared by thermal decomposition onto BaTiO3 surface from
Marija Šuljagić   +7 more
doaj   +1 more source

Study of the Effect of Two Phases in Li4SiO4–Li2SiO3 Ceramics on the Strength and Thermophysical Parameters

open access: yesNanomaterials, 2022
The paper studies the effect of Li2SiO3/Li4SiO4 phase formation in lithium-containing ceramics on the strength and thermophysical characteristics of lithium-containing ceramics, which have great prospects for use as blanket materials for tritium ...
Artem Kozlovskiy   +5 more
doaj   +1 more source

Construction and Characterization of TiN/Si3N4 Composite Insulation Layer in TiN/Si3N4/Ni80Cr20 Thin Film Cutting Force Sensor

open access: yesMicromachines, 2021
The measurement of cutting force is an effective method for machining condition monitoring in intelligent manufacturing. Titanium nitride films and silicon nitride films were prepared on 304 stainless steel substrates by DC-reactive magnetron sputtering ...
Ruyuan Ma   +5 more
doaj   +1 more source

The Casting Rate Impact on the Microstructure in Al–Mg–Si Alloy with Silicon Excess and Small Zr, Sc Additives

open access: yesMetals, 2021
The study investigates the effect of casting speed on the solidification microstructure of the aluminum alloy Al0.3Mg1Si with and without the additions of zirconium and scandium. Casting was carried out in steel, copper, and water-cooled chill molds with
Evgenii Aryshenskii   +5 more
doaj   +1 more source

Home - About - Disclaimer - Privacy