Results 161 to 170 of about 4,948,518 (287)

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

Influence of Propolis Extract on Bleaching Effectiveness and Enamel Physical Properties. [PDF]

Acta Stomatol Croat
Andrade da Silva J, Alves E Cavalheiro R, Dos Santos DM, Aguiar FHB, Lima DANL.   +4 more
europepmc   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

High-temperature physical properties of tungsten: implications for near-field thermophotovoltaic energy conversion. [PDF]

RSC Adv
Cuong TD, Phan AD.
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Effect of Gamma Radiation on the Chemical Structure and Physical Properties of Poly(butylene adipate-co-terephthalate). [PDF]

Polymers (Basel)
Marcos Rios D, Atrous MA, Belhaoues A, Burillo G, Navarro R, Marcos-Fernández Á.   +5 more
europepmc   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Structural and Physical Properties of Chitosan Films Containing UV-Driven <i>In Situ</i> Growth of Silver Nanoparticles. [PDF]

ACS Omega
Costa D, Cascione M, De Matteis V, Di Corato R, Gallo N, Villani S, Demitri C, Alifano P, Sannino A, Cuniberti G, Rinaldi R.   +10 more
europepmc   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Impact of Waste-HydroChar on the Rheological Behavior, Physical Properties, and Aging Resistance of Bitumen. [PDF]

Materials (Basel)
Dintcheva NT, Teresi R, Graziano F, Infurna G, Volpe M, Messineo A, Celauro C.   +6 more
europepmc   +1 more source