Results 41 to 50 of about 1,055 (251)
International Journal of Horticultural Science, 2004 One of our objectives in the apple breeding program of the Department of Fruit Science, beside creating new varieties, is to search for new gene sources.
M. G. Tóth, Sz. Kovács
doaj +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
New Products against Apple Scab and Powdery Mildew Attack in Organic Apple Production
Notulae Botanicae Horti Agrobotanici Cluj-Napoca, 2010 Interspecific hybridizations represent one of the apple breeding methods by which a wide variability can be achieved, useful for creating new cultivars.
Viorel MITRE +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Notulae Botanicae Horti Agrobotanici Cluj-Napoca, 2010 Interspecific hybridizations represent one of the apple breeding methods by which a wide variability can be achieved, useful for creating new cultivars.
Radu E. SESTRAS +5 more
doaj +1 more source
Quantitative Traits of Interest in Apple Breeding and Their Implications for Selection
Plants, 2023 Apple breeding is a laborious and long-lasting process that requires qualified resources, land, time, and funds. In this study, more than 5000 F1 apple hybrids from direct and testcrosses were analyzed.
Radu E. Sestras, Adriana F. Sestras
doaj +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Frontiers in Microbiology, 2021 For soilborne pathogens, germination of the resting or dormant propagule that enables persistence within the soil environment is a key point in pathogenesis.
Sadegh Balotf +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source