Results 131 to 140 of about 4,690,273 (294)
Advanced Engineering Materials, EarlyView.Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar +3 more
wiley +1 more source
On the effect of pre-oxidation on the nitriding kinetics
, 2000 The oxidation of ferritic surfaces prior to gaseous nitriding has been reported to lead to improved uniformity of the compound layer thickness and enhanced nitriding kinetics. The present work considers the nucleation and growth of a model compound layer
Somers, Marcel A. J. +1 more
core
D peak width from Raman spectra pre and post oxidation at 450°C.
, 2016 D peak width from Raman spectra pre and post oxidation at 450°C.
Liam Payne (827772) +2 more
core +1 more source
Electrodeposition in Structural Lattices of Variable Architectures
Advanced Engineering Materials, EarlyView.Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A thermoplastic PMMA‐based photoresin enables high‐resolution DLP printing followed by solvent‐vapor smoothing. The treatment reduces staircase‐induced surface roughness from 2.33 µm to 129 nm and increases visible‐light transmittance from approximately 30% to 80%, providing a route toward transparent PMMA components for rapid prototyping and non ...
Rozhin Heydarpour +5 more
wiley +1 more source
Open CeramicsThe effect of thermal pre-oxidation on the microstructure and molten-salt interaction of MgO–316L composite anodes produced from decarbonized MgO–C refractory recyclate was investigated. Composite anodes containing 40 vol.% recycled MgO and 60 vol.% AISI
Alexander Adamczyk +8 more
doaj +1 more source
Pre-growth dependent phenotypes for P. aeruginosa nitrate reductase mutants.
Left: When cultures were pre-grown in slanted shaking tubes, providing the cultures ample oxygen, only the ΔnapAB strain (orange) had a PCA oxidation deficit. Right: Pre-growing the cultures in standing tubes without nitrate supplementation also leads to
Lev M. Z. Tsypin (18510253) +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.The ALD precursor bis(trimethylsilyl)selenide is simultaneously a substrate surface inhibitor. It allows for the growth of Sb2Se3 in combination with tris(dimethylamido)antimony, but also silylates surface hydroxyl groups on the substrate if such hydroxyls are present.
Pei‐Chun Liao +9 more
wiley +1 more source
Atmospheric alkaline pre-oxidation of refractory sulphide gold ores
, 2018 Four iron-sulphide-containing gold ores from the White Mountain mine in the Jilin Province, China were studied to examine the benefits of using oxidative treatment prior to conventional cyanidation to leach gold.
Rego, Alan Joseph
core +1 more source
Edible Cuttlefish Ink: Complex Chemistry, Structure, and Electrical Response
Advanced Engineering Materials, EarlyView.An integrated approach of chemistry‐structure‐electrical properties is used to assess the potential of edible cuttlefish ink as a bio‐based conductive ink for printable electronics. Chromatography and Neutron Activation Analysis reveal a fascinating molecular and elemental diversity.
Camille Bour‐Cardinal +5 more
wiley +1 more source