Results 91 to 100 of about 4,566,256 (295)
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
MicroCT study on the enamel mineral density of primary molars
, 2016 Aim The aim of this study is to report on the mineral density of the enamel of primary molars related to the age of the child and to compare the mineral density of sound and carious enamel in those molars.
ten Cate, J.M. +4 more
core +2 more sources
Clinical, Cosmetic and Investigational Dentistry, 2021 Mannaa K Aldowsari,1 Musab Alsaidan,2 Marshad Alaqil,2 Ali BinAjian,2 Jawad Albeialy,2 Mohammed Alraawi,3 Mohammed M Al Moaleem4 1Department of Pediatric Dentistry and Orthodontics, College of Dentistry, King Saud University, Riyadh, Saudi Arabia ...
Aldowsari MK +6 more
doaj
Advanced Engineering Materials, EarlyView.A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi +3 more
wiley +1 more source
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
Advanced Engineering Materials, EarlyView.An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
Natal maxillary primary molars: Case report
, 2004 An unusual case of a newborn with two immature natal maxillary molars is presented. Clinical and histological examination showed that the teeth were rootless and incompletely mineralized.
Galassi, Marlei Seccani +2 more
core +1 more source
The effects of unilateral premature loss of maxillary primary molars on the dental arch dimensions
Journal of Baghdad College of Dentistry, 2013 Background: The aim of the study was to evaluate the amount of changes in the horizontal and vertical maxillary arch dimensions measurements following the premature loss of primary molars.
Dunia A Al-Dulayme
doaj
Advanced Engineering Materials, EarlyView.This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig +2 more
wiley +1 more source
Success Rate of Zinc Oxide Eugenol in Pulpectomy of Necrotic Primary Molars: A Retrospective Study [PDF]
Journal of Dental Materials and Techniques, 2015 Introduction: Pulpectomy is a conservative treatment plan for primary necrotic teeth and Zinc Oxide Eugenol is still a good choice as root canal filling material but long term studies on poor prognosis molars are limited and almost contradictory.
Zahra Bahrololoomi, , Shiva Zamaninejad
doaj
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source