Results 91 to 100 of about 55,078 (219)
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.In situ synchrotron high‐energy X‐ray diffraction reveals the real‐time high‐temperature phase evolution of a ternary V‐9Si‐6.5B alloy. The study uncovers a kinetically delayed V5SiB2 → V8SiB4 transformation governed by massive structural and chemical barriers.
Zahra Sabeti +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley +1 more source
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz +4 more
wiley +1 more source
Design of a Multistable Finger Prosthesis with Programmable Metamaterials
Advanced Engineering Materials, EarlyView.This research article shows the development of a multistable programmble metamaterial for the use as a finger prosthesis. The material was designed on different hierarchical levels where the influence of geometrical parameters and combination of mechanical elements was explored.
Franziska Wenz +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová +6 more
wiley +1 more source
Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System
Advanced Engineering Materials, EarlyView.Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner +7 more
wiley +1 more source
A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation
Advanced Engineering Materials, EarlyView.A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler +4 more
wiley +1 more source
Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy
Advanced Engineering Materials, EarlyView.An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa +6 more
wiley +1 more source