Results 151 to 160 of about 4,574,423 (281)

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Addressing Incidental Findings in Neuroimaging Studies: Never Easy, Rarely Rescue. [PDF]

Ethics Hum Res
Nix HP.
europepmc   +1 more source

Novel Tailoring of Ternary ZnS‐MXene‐TiO2 Nanocomposite Heterojunction and Its Tunable Electrochemical Properties With Enhanced Photocatalytic Degradation

Advanced Engineering Materials, EarlyView.
ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir, Dohyun Kim, Minho Song, Jae Doc Na, Young Jun Joo, Kwang Youn Cho, Karna Wijaya, Won‐Chun Oh   +7 more
wiley   +1 more source

Development and content evaluation of a multidimensional coping model-based health education manual for dementia care support. [PDF]

Front Public Health
Wu J, Zhang D, Feng L, Zhao Q, Xiao M, Wang J.   +5 more
europepmc   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

From Research to Practice: Enhancing Creativity Awareness in Education. [PDF]

Behav Sci (Basel)
Can I, Bart WM.
europepmc   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

The Secure Base in the Storm: How Parent-Child Bonds Shape Coping in Pediatric Cancer Caregiving. [PDF]

Pediatr Rep
Rizzi D, Barone L, Balestra A, Montanaro M, Nichelli F, Schivalocchi E, Rampoldi G, Spinelli M, Ciuffo G, Brescia LP, Cecinati V, Zecca M, Greco C, Lionetti F, Rotella J, Gambini G, Klersy C, Ionio C.   +17 more
europepmc   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source