Results 221 to 230 of about 660,436 (258)
Some of the next articles are maybe not open access.
The effect of additives on the pulsed electrodeposition of copper
Transactions of the IMF, 2005The pulsed electrodepostion of copper has been systematically investigated from a copper sulphate bath.
Mohan, S., Raj, V.
openaire +1 more source
Pulse and Pulse/Reverse Techniques for Electrodeposition of Rhenium and Refractory Metals
ECS Meeting Abstracts, 2023Refractory metals possess unique properties including high melting points, high hardness at room temperature, chemical resistance, and high density. Electrodeposition of refractory metals is of interest as a scalable approach to apply uniform coatings to enable a wide range of applications in aerospace, nuclear, catalysis, biomedical fields.
Daniel E Hooks +4 more
openaire +1 more source
Pulsed Electrodeposition of Ni‐Mo Alloys
Journal of The Electrochemical Society, 1988The effect of pulsing the current on the composition, the internal stress, and mechanical properties of Ni-Mo electrodeposits was investigated. The molybdenum, content increased with increasing peak current density and to a lesser degree with decreasing duty cycle.
C. C. Nee, W. Kim, R. Weil
openaire +1 more source
Pulsed electrodeposition of layered brass structures
Metallurgical Transactions A, 1988The mechanical properties of electroplated alpha and beta brasses and of deposits consisting of alternate layers of the two phases were determined. The alternate-layer deposits were stronger than the single-phase ones only if the latter were coarse grained.
R. Weil, C. C. Nee, J. W. Chang
openaire +1 more source
Pulsed Electrodeposition of Zinc–Manganese Alloys
Russian Journal of Electrochemistry, 2001High-quality Zn-Mn coatings with an Mn content reaching 50% are obtained from citrate-sulfate solutions in pulsed electrolysis at a pulse length of 0.1 ms to 1 s. Due to the formation of a blocking film of citrate-hydroxide zinc compounds, cathodic potential increases with time, which helps reach a codeposition potential of Mn ions.
F. I. Danilov +2 more
openaire +1 more source
Pulsed electrodeposition of Zn in the presence of surfactants
Electrochimica Acta, 2006Abstract The preparation of Zn deposits has been performed by galvanostatic pulsed electrolysis, from acidic zinc sulphate solutions, on a stainless steel substrate. The influence of the surfactants (cetyl trimethyl ammonium bromide (CTAB), sodium dodecyl sulphate (SDS) and octylphenolpoly(ethyleneglycolether)n, n = 10, Triton X-100) on the ...
A. Gomes, M.I. da Silva Pereira
openaire +1 more source
Pulse electrodeposition of Ni–SiC nanocomposite
Materials Letters, 2002Abstract Nanocomposites consisting of a nanocrystalline Ni matrix (grain sizes 15–20 nm) reinforced with sub-micron size SiC particulates up to 3 wt.% have been produced by pulsed current electrodeposition. Microhardness values were about two times higher than those for comparable polycrystalline Ni–SiC composites, primarily due to the hard ...
A.F Zimmerman +3 more
openaire +1 more source
Powder Pulse Electrodeposition for Additive Manufacturing
ECS Meeting Abstracts, 2017Electrodeposition is commonly used for the deposition of metallic and composite coatings. It is useful as it can coat complex 3D structures and can be used for the deposition of alloys. There are a few disadvantages; it is relatively slow to build up thick coatings and in some cases the current efficiency can be low.
Andrew P Abbott +2 more
openaire +1 more source
Pulse plating effects in nickel electrodeposition
Surface and Coatings Technology, 1989Abstract The effects of pulse plating on the mechanical properties and internal stresses of nickel deposits were investigated. The yield and tensile strengths increased as a result of pulse plating especially at high peak current densities because of grain refinement.
Wonbaek Kim, Rolf Weil
openaire +1 more source
Pulsed Electrodeposition of Iron‐Nickel Alloys
Journal of The Electrochemical Society, 1990This paper reports on the effects of dc, pulse, and pulse reverse current waveforms on deposition of Fe-Ni alloys studied in unagitated solutions and with a rotating cylindrical electrode. A nickel sulfamate/ferrous chloride electrolyte system at pH 2 less than 2 A/dm{sup 2}.
David L. Grimmett +2 more
openaire +1 more source

