Results 81 to 90 of about 166,378,893 (241)
Additive Manufacturing of Alumina‐Reinforced Elastomers
Advanced Engineering Materials, EarlyView.Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani +6 more
wiley +1 more source
An Elementary Study of a Class of Dynamic Systems with Two Time Delays
Cubo, 2012 An elementary analysis is developed to determine the stability region of a certain class of ordinary differential equations with two delays. Our analysis is based on determining stability switches first where an eigenvalue is pure complex, and then ...
Akio Matsumoto, Ferenc Szidarovszky
doaj
Scientific ReportsRecycled polyethylene terephthalate (RPET) was doped with Neodymium Oxide (Nd2O3: 0, 1, 2, 4, and 8 wt.%) to investigate its structural, optical, dielectric, and mechanical properties. X-ray diffraction (XRD) analysis revealed that pure RPET exhibited an
Amr Antar +7 more
doaj +1 more source
Applied SciencesAs coal resource development progresses deeper underground, the increasing depth of mine shafts poses significant challenges to the safety and stability of traditional shaft construction methods, further compounding operational difficulties.
Zhijiang Yang +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The OntOMat ontology establishes a structured framework for polymer matrix fiber reinforced composite materials, integrating manufacturing processes, characterization methods, and multiscale design through the VDI/VDE 3682 formalized process description standard.
Nicolas Christ +19 more
wiley +1 more source
Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys
Advanced Engineering Materials, EarlyView.An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi +5 more
wiley +1 more source
Multilayer Self‐Limiting Electrospray Deposition via Stepped Voltage Bias
Advanced Engineering Materials, EarlyView.Self‐limiting electrospray deposition (SLED) uses a high voltage to generate and deposit a charged payload on a target surface. The coating retains its charge, repelling newly arriving material. SLED thickness can be decreased by applying a secondary bias to the target.
Madhuri Deb +3 more
wiley +1 more source
Beyond Bryan: Builders' liability and pure economic loss [PDF]
, 2005 In Bryan v Maloney, the High Court extended a builder’s duty of care to encompass a liability in negligence for the pure economic loss sustained by a subsequent purchaser of a residential dwelling as a result of latent defects in the building’s ...
Carver, Tracey L.
core +1 more source
Kuwait Journal of ScienceThe present study investigates the reactions of polystyrene and epoxy/polystyrene powder composites, exploring different weight percentages (8%, 12%, and 16%) of polystyrene during decomposition under highly elevated temperatures within a nitrogen ...
Jubier N.J., Al-Jorani K.R., Ali A.A.
doaj +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source