Results 61 to 70 of about 100,965 (261)

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Radial variation of solar‐wind parameters

Geophysical Research Letters, 1976
It is demonstrated that since fluctuations in the solar wind are not small, they can have important effects on the observed average values of parameters in the solar wind and their radial variation. The effect is distinct from the dynamical effect of waves and turbulence and results from the averaging process.
openaire   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Genetic Versus Environmental Influence on Radial Variation in Myracrodruon urundeuva Wood

Floresta e Ambiente, 2017
We hypothesized that Myracrodruon urundeuva trees of two provenances with different genotypes would present variations influenced by their origin terms of anatomy and specific gravity when planted in an environment different from their seed origin, but ...
Eduardo Luiz Longui, Gabriela Trindade Pires, Miguel Luiz Menezes Freitas, Diego Romeiro, Sandra Monteiro Borges Florsheim, Antonio Carlos Scatena Zanatto   +5 more
doaj   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Modeling of radial growth curves and radial variation of basic density in Chamaecyparis obtusa planted in two progeny test sites

Journal of Wood Science
The objectives of the present study are to clarify the effect of macro- and micro-environment on the radial growth patterns and radial variation patterns of basic density in hinoki cypress (Chamaecyparis obtusa (Sieb. et Zucc.) Endl.).
Yusuke Takahashi, Futoshi Ishiguri, Michinari Matsushita, Ikumi Nezu, Jyunichi Ohshima, Shinso Yokota, Akira Tamura, Miyoko Tsubomura, Makoto Takahashi   +8 more
doaj   +1 more source

Anatomic Variation in the Origin and Course of Radial Artery: A Descriptive Cross-Sectional Study

Journal of Nepal Medical Association, 2019
Introduction: The radial artery is commonly originated from the brachial artery in the cubital fossa at the level of the neck of the radius. It is the artery of choice for coronary artery angiography, percutaneous coronary artery intervention ...
Muna Kandel, Shanta Hada, Bishwo Prachanda Sedhain   +2 more
doaj   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source