Results 41 to 50 of about 22,209 (309)
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
PhotonicsTo enable mains-free wireless access in confined environments such as tunnels and mines, this paper proposes and experimentally demonstrates a converged power-over-fiber (PoF) and analog radio-over-fiber (A-RoF) system over a single standard single-mode ...
Guangxin Li +4 more
doaj +1 more source
Multifunctional operation of a fiber Bragg grating in a WDM/SCM radio over fiber distribution system [PDF]
, 2004 A radio over fiber distribution system incorporating both sub-carrier multiplexing (SCM) and wavelength division multiplexing (WDM) technologies is presented.
Anandarajah, Prince M. +2 more
core +1 more source
Controlling Rayleigh-Backscattering-Induced Distortion in Radio over Fiber Systems for Radioastronomic Applications [PDF]
, 2020 Radio over Fiber (RoF) Systems exploiting a direct modulation of the laser source are presently utilized within important Radioastronomic scenarios. Due to the particular operating conditions of some of these realizations, the phenomena which typically ...
Giovannini, Andrea +8 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
2
IEEE Photonics Journal, 2018 Offset-QAM-based filterbank multicarrier (FBMC-OQAM) is an attractive modulation candidate to increase the spectral efficiency of radio-over-fiber and fiber–wireless systems.
Francois Rottenberg +6 more
doaj +1 more source
Future broadband access network challenges [PDF]
, 2010 Copyright @ 2010 IEEEThe optical and wireless communication systems convergence will activate the potential capacity of photonic technology for providing the expected growth in interactive video, voice communication and data traffic services that are ...
Abdollahi, SR +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
Radio-over-fiber transmission using vortex modes [PDF]
2015 International Topical Meeting on Microwave Photonics (MWP), 2015 This paper demonstrates experimentally the distribution of radio-over-fiber (RoF) signals using orbital angular momentum (OAM) of light over standard OM4 multimode fiber (MMF) at 850 nm wavelength. Five independent OAM modes are used to convey RoF signals in the microwave regime showing robust performance and therefore opening new prospects for ...
Tatarczak, A. +5 more
openaire +1 more source
Enhancing Bubble Removal in Geometry‐Optimized Electrodes
Advanced Engineering Materials, EarlyView.3D‐printed lattice electrodes outperform stochastic foams in alkaline water electrolysis despite 20%–25% lower surface area. Straight flow channels generate Venturi‐like bubble entrainment, suppressing gas accumulation that renders foam interiors electrochemically inactive.
Florian Wiesner +5 more
wiley +1 more source