Results 61 to 70 of about 32,523 (343)
Intra-pulse Cavity Enhanced Measurements of Carbon Monoxide in a Rapid Compression Machine
, 2018 A laser absorption sensor for carbon monoxide concentration was developed for combustion studies in a rapid compression machine using a pulsed quantum cascade laser near 4.89 μm.
Farooq, Aamir, Nasir, Ehson Fawad
core +1 more source
Experimental Investigation in the Autoignition Behaviour of Aviation Jet Fuel in a Rapid Compression Machine [PDF]
, 2021 : Jet A-1 fuel’s autoignition behaviour was examined experimentally in a newly developed rapid compression machine (RCM) at the University of Sheffield.
Ebieto, C.E +5 more
core +1 more source
Open-Source Grinding Machine for Compression Screw Manufacturing
Inventions, 2020 Some of the most promising distributed recycling and additive manufacturing (DRAM) technical systems use fused particle fabrication (FPF) or fused granular fabrication (FGF), where compression screws force post-consumer waste plastic through a heated ...
Jacob Franz, Joshua M. Pearce
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
A single n-heptane droplet behavior in rapid compression machine
, 2014 This study investigated the evaporation characteristics of a single n-heptane droplet inside a rapid compression machine (RCM). The RCM is an experimental apparatus used to simulate a single compression stroke of an internal combustion engine to observe ...
Baek, Seung-Wook +2 more
core +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
-Octane and Ethanol in an Optical Rapid Compression Machine
, 2022 With the introduction of EV technology into the light-duty vehicle market, the demand for gasoline in conventional spark ignition engines is projected to decline in the coming decades.
Adam Dempsey +5 more
core +1 more source
Analysis of rapid compression machine facility effects on the auto-ignition of ethanol
, 2020 Ignition delay measurements are frequently carried out in Rapid Compression Machines (RCMs), which require a means to prepare mixtures of fuel, oxidizer and diluent gases. In RCMs, the same compressed conditions can be achieved by various combinations of
Chaitanya Wadkar +2 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Effect of fuel-air mixture dilution on knock intensity
Nihon Kikai Gakkai ronbunshu, 2016 Effect of fuel-air mixture diluted by inert gas on knock intensity was investigated by using a rapid compression and expansion machine. Dilution of fuel-air mixture decreased knock intensity.
Mitsuaki OHTOMO +2 more
doaj +1 more source