Results 61 to 70 of about 143,541 (299)
Pharmaceutics, 2020 This study aimed to elucidate the impact of a common anionic surfactant, sodium dodecyl sulfate (SDS), along with hydroxypropyl cellulose (HPC) and Soluplus (Sol) on the release of griseofulvin (GF), a poorly soluble drug, from amorphous solid ...
Mahbubur Rahman +4 more
doaj +1 more source
Metals, 2021 Mg–2Y–0.6Nd–0.6Zr alloy was first deformed by equal channel angular pressing (ECAP), then rolled and deformed under ultralow temperature conditions (liquid nitrogen immersion), and finally annealed.
Hongmin Yu +3 more
doaj +1 more source
, 2008 We show that Pr${_{0.5}}$Ca$_{0.5}$MnO${_3}$ with 2.5% Al substitution and La${_{0.5}}$Ca$_{0.5}$MnO${_3}$ (LCMO) exhibit qualitatively similar and visibly anomalous M-H curves at low temperature.
A Banerjee +14 more
core +1 more source
Evaluation and control of mechanical degradation of austenitic stainless 310S steel substrate during coated superconductor processing [PDF]
, 2018 The superconductor industry considers cold-rolled austenitic stainless 310S steel a less expensive substitute for Hastelloy X as a substrate for coated superconductor. However, the mechanical properties of cold-rolled 310S substrate degrade significantly
Kim, Najung +4 more
core +1 more source
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Microstructure and mechanical behavior of CrCoNi medium entropy alloys in 1000 MPa grade
Journal of Aeronautical Materials, 2020 The ultrafine-grained (UFG) CrCoNi medium entropy alloys (MEAs) with excellent mechanical and tribological performances were fabricated by combining rolling deformation and annealing treatment.
SONG Lingyun +7 more
doaj +1 more source
Hot ductility and deformation behavior of C-Mn/Nb-microalloyed steel related to cracking during continuous casting [PDF]
, 2014 Hot ductility studies have been performed on C-Mn and C-Mn-Nb steels with an approach to simulate the effect of cooling conditions experienced by steel in secondary cooling zone during continuous casting.
Lanjewar, Harishchandra +3 more
core +1 more source
Bio‐Inspired Molecular Events in Poly(Ionic Liquids)
Advanced Functional Materials, EarlyView.Originating from dipolar and polar inter‐ and intra‐chain interactions of the building blocks, the topologies and morphologies of poly(ionic liquids) (PIL) govern their nano‐ and micro‐processibility. Modulating the interactions of cation‐anion pairs with aliphatic dipolar components enables the tunability of properties, facilitated by “bottom‐up ...
Jiahui Liu, Marek W. Urban
wiley +1 more source
Microstructure Evolution in ODS Alloys with a High-Volume Fraction of Nano Oxides
Metals, 2018 Existing oxide dispersion strengthened (ODS) alloys are, besides Ni-based superalloy single crystals, the most creep-resistant materials. The creep resistance of the ODS alloys may, moreover, be significantly improved thanks to increasing the volume ...
Jiří Svoboda +6 more
doaj +1 more source
Typomorphism of perthitic intergrowth of feldspars from granitic pegmatites from the area of west Azov (Ukrainian shield) [PDF]
, 2014 Приведены данные о вещественном составе графических пегматитов с различной специализацией кварца и отмечено широкое развитие пертитовых вростков в полевых шпатах.
Slivnaya, E. V. +2 more
core