Results 41 to 50 of about 39,326 (254)
Pharmaceutics, 2020 This study aimed to elucidate the impact of a common anionic surfactant, sodium dodecyl sulfate (SDS), along with hydroxypropyl cellulose (HPC) and Soluplus (Sol) on the release of griseofulvin (GF), a poorly soluble drug, from amorphous solid ...
Mahbubur Rahman +4 more
doaj +1 more source
Metals, 2021 Mg–2Y–0.6Nd–0.6Zr alloy was first deformed by equal channel angular pressing (ECAP), then rolled and deformed under ultralow temperature conditions (liquid nitrogen immersion), and finally annealed.
Hongmin Yu +3 more
doaj +1 more source
Elastic Properties and Thermal Expansion Behavior of a Polycrystalline VMnFeCoNi High‐Entropy Alloy
Advanced Engineering Materials, EarlyView.The high‐entropy alloy (HEA) V20Mn20Fe20Co20Ni20 (composition in at.%) can be made single‐phase face‐centered cubic (FCC) when annealed above 1338 K followed by water quenching. In this state, the alloy exhibits the greatest strength‐ductility combination of any quinary single‐phase FCC HEA.
Guillaume Laplanche +3 more
wiley +1 more source
Microstructure and mechanical behavior of CrCoNi medium entropy alloys in 1000 MPa grade
Journal of Aeronautical Materials, 2020 The ultrafine-grained (UFG) CrCoNi medium entropy alloys (MEAs) with excellent mechanical and tribological performances were fabricated by combining rolling deformation and annealing treatment.
SONG Lingyun +7 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath +2 more
wiley +1 more source
Microstructure Evolution in ODS Alloys with a High-Volume Fraction of Nano Oxides
Metals, 2018 Existing oxide dispersion strengthened (ODS) alloys are, besides Ni-based superalloy single crystals, the most creep-resistant materials. The creep resistance of the ODS alloys may, moreover, be significantly improved thanks to increasing the volume ...
Jiří Svoboda +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt +5 more
wiley +1 more source
TRANSFORMATION KINETICS FOR NUCLEATION ON RANDOM PLANES AND LINES
Image Analysis and Stereology, 2011 Birth and growth processes are known in materials science as nucleation and growth processes. In crystalline materials nucleation almost always takes place in an internal crystalline defect. These defects are classified according to their dimensionality:
Elena Villa, Paulo R Rios
doaj +1 more source
Advanced Engineering Materials, EarlyView.Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali +5 more
wiley +1 more source
State-of-the-Art Review of the Simulation of Dynamic Recrystallization
MetalsThe evolution of microstructures during the hot working of metallic materials determines their workability and properties. Recrystallization is an important softening mechanism in material forming that has been extensively researched in recent decades ...
Xin Liu +5 more
doaj +1 more source