Results 101 to 110 of about 90,982 (263)

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Consumed by Abdominal Distention

Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge, James Grenert, Brian Haas, Mary Margaretten   +3 more
wiley   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel, Lara Kuhr, Khemais Barienti, Sebastian Herbst, Florian Nürnberger, Hans Jürgen Maier, Marc C. Wurz   +6 more
wiley   +1 more source

Impact of Sustainable Binders Based on Lignin and Collagen on the Volume Stability and Mechanical Properties of MgO‐C Refractories with MgO‐C Recyclates

Advanced Engineering Materials, EarlyView.
Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller, Florian Kerber, Kirsten Moritz, Steffen Dudczig, Konstantin Kraushaar, Thomas Schemmel, Jana Hubálková, Patrick Gehre, Christos G. Aneziris   +8 more
wiley   +1 more source

Skills escalator in allied health: a time for reflection and refocus

Journal of Healthcare Leadership, 2011
Lisa G Gilmore1, Joanne H Morris1, Karen Murphy2, Karen Grimmer-Somers3, Saravana Kumar31The Canberra Hospital, ACT Government Health Directorate, Canberra, ACT; 2ACT Government Health Directorate, Canberra, ACT; 3International Centre for Allied Evidence,
Gilmore LG, Morris JH, Murphy K, Grimmer-Somers K, Kumar S   +4 more
doaj  

Creating Ti–Fe α/β Alloys by Diffusion‐Driven Solid‐State Processing

Advanced Engineering Materials, EarlyView.
This study proposes making alloys containing fast diffusing elements that are difficult to produce by ingot metallurgy, by diffusion‐driven solid‐state HIP processing of elemental powders and low‐temperature homogenisation. Here, novel Fe‐Ti α–β alloys are formed having fine α–β lamellae, a small β prior grain size without significant intermetallics ...
Jiaqi Xu, Xun Zhang, Jack M. Donoghue, Albert D. Smith, Rahul Unnikrishnan, Rhys Thomas, Vahid Nekouie, Jie Luo, Dongchen Hu, Michael Preuss, Philip J. Withers   +10 more
wiley   +1 more source