Results 231 to 240 of about 89,955 (290)

Non‐Continuous Iridescent Variable Structural Color Based on Metallic Surface Periodic Structures

Advanced Materials Interfaces, EarlyView.
This study presents an ink‐free laser nanofabrication technique that generates periodic arched microstructures on titanium surfaces, achieving non‐continuous iridescent dual‐color switching. The ridge and side flanks of these structures possess distinct oxide film thicknesses, enabling angle‐dependent selective reflection of specific wavelengths.
XiangWei Liu, XiaoSong Yu, Jiao Geng, LiPing Shi   +3 more
wiley   +1 more source

A Reusable Polymeric Sensor Based on Green‐Synthesized CQDs@ZIF‐8 for the Rapid Detection of Nitro‐Explosive Picric Acid

Advanced Materials Interfaces, EarlyView.
This study presents the rational design and synthesis of a highly luminescent polymeric nanocomposite. Initially, highly fluorescent carbon quantum dots (CQDs) are synthesized via a facile hydrothermal method using citric acid and β‐alanine as precursors, followed by rigorous purification through centrifugation and filtration.
Yunus Emre Toprak, Soner Çubuk, Memet Vezir Kahraman   +2 more
wiley   +1 more source

Mechanical Stress Evolution in Polycrystalline Ge Thin Films Under MeV Ion Irradiation

Advanced Materials Interfaces, EarlyView.
Irradiation of polycrystalline Ge thin films with 1.8 MeV Au ions alters residual stress through defect generation and lattice expansion. Increasing fluence drives progressive lattice disorder and eventual amorphization. Polycrystalline Ge resists amorphization longer than crystalline Ge, as grain boundaries facilitate defect diffusion, significantly ...
Karla J. Paz Corrales, Aaron Reupert, Kevin Lubig, Frank A. Müller, Berit Marx‐Glowna, Ralf Röhlsberger, Till Weickhardt, Giancarlo Soavi, Martin Hafermann, Elke Wendler, Carsten Ronning   +10 more
wiley   +1 more source

Atomic Layer Deposition of Metallic Molybdenum Dioxide Thin Films Enabling High‐k Rutile Capacitors

Advanced Materials Interfaces, EarlyView.
The first direct atomic layer deposition (ALD) process of molybdenum dioxide (MoO2) thin films is reported using molybdenum(II) acetate dimer (Mo2(OAc)4) and oxygen (O2) as precursors at 235°C–275°C. The films are crystalline, exceptionally pure, and conductive.
Alexey Ganzhinov, Miika Mattinen, Marko Vehkamäki, Kenichiro Mizohata, Mykhailo Chundak, Georgi Popov, Paavo Porri, Mikko Ritala, Matti Putkonen   +8 more
wiley   +1 more source

Hydrogel‐Based 3D‐Printable Stretchable Pressure Sensor

Advanced Materials Technologies, EarlyView.
We present a carbon‐black‐functionalized double‐network granular hydrogel (DNGH) pressure sensor capable of detecting pressures from 200 Pa, equivalent to a light finger touch, up to 500 kPa. The sensor exhibits signal drifts below 3.5% after 800 cycles and response times around 80 ms. Leveraging this broad sensing range, we 3D print this material into
Tianyu Yuan, Chenzhuo Li, Antonia Georgopoulou, John M. Kolinski, Esther Amstad   +4 more
wiley   +1 more source

3D Printed Multimaterial Microfluidic Transistors

Advanced Materials Technologies, EarlyView.
We introduce a biocompatible, high resolution photopolymer resin that closely mimics the Young's Modulus (elasticity) and reversible stretchability (no hysteresis) of poly(dimethylsiloxane) (PDMS), enabling the fabrication of microfluidic transistors (i.e., microvalves capable of proportional amplification) by multimaterial stereolithography (mSLA ...
Alireza Ahmadianyazdi, Wei Huang, Kaustav A. Gopinathan, Ivan Stepanov, Lisa Horowitz, Ting‐Yuan Tu, Mehmet Toner, Albert Folch   +7 more
wiley   +1 more source

3D Printing of Highly Dense and Translucent Zirconia Parts for Dental Applications: Effect of Filament Overlapping

Advanced Materials Technologies, EarlyView.
This study formulated a 5Y‐PSZ zirconia paste for extrusion‐based additive manufacturing via direct ink writing, producing dense ceramic structures for dental applications. A colloidal approach with 47 vol% nanometric powder and tailored additives optimized rheology and printability.
Juliana de Freitas Gouveia Silva, Manuel Fellipe Rodrigues Pais Alves, Ana Carolina da Silva, Tiago Moreira Bastos Campos, Renata Marques De Melo, Susana Maria Henriques Olhero   +5 more
wiley   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Ultrasensitive photonic crystal fiber refractive index sensor

Optics Letters, 2009
We introduce a microfluidic refractive index sensor based on a directional coupler architecture using solid-core photonic crystal fibers. The sensor achieves very high sensitivity by coupling the core mode to a mode in the adjacent fluid-filled waveguide that is beyond modal cutoff, and with strong field overlap.
Darran K C, Wu, Boris T, Kuhlmey, Benjamin J, Eggleton   +2 more
openaire   +4 more sources

Fiber SPR refractive index sensor with the variable core refractive index

Applied Optics, 2020
In this paper, a refractive index sensor based on the control of the fiber core refractive index is proposed. By employing ultraviolet curable adhesive with the different refractive index and hollow capillary fiber, the special fiber with a variable core refractive index is fabricated.
Chunlan Liu, Xin Zhang, Yachen Gao, Yong Wei, Ping Wu, Yudong Su, Peng Wu   +6 more
openaire   +2 more sources