Results 171 to 180 of about 50,857 (288)

Comprehensive reconstruction of the musculoskeletal anatomy in the shoulder using a hybrid 3D ultrasound mosaicking workflow: A pilot study. [PDF]

PLoS One
Sewify A, Steffens M, Perrier N, Antico M, Lavaill M, Edwards C, Pivonka P, Fontanarosa D.   +7 more
europepmc   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Deep learning approaches for head pose estimation in sports impacts. [PDF]

Sports Eng
Aston T, Machtsiras G, Teixeira-Dias F.
europepmc   +1 more source

Machine Learning‐Supported Analysis for Predicting and Visualizing Nonlinear Relationships Between Material Properties in Electroplated Chromium Layers

Advanced Engineering Materials, EarlyView.
This study applies machine learning regression to predict chromium layer thickness in decorative trivalent chromium electroplating, using 441 experiments from laboratory‐scale (1L) and pilot‐scale (14L) setups. Tree‐based models, particularly CatBoost, outperformed linear regression by capturing nonlinear parameter interactions (R2$R^2$ up to 0.77 ...
Christoph Baumer, Christopher Mai, Luca Eisentraut, Andreas Bund, Ricardo Buettner   +4 more
wiley   +1 more source

A Guide to Structureless Visual Localization. [PDF]

Int J Comput Vis
Panek V, Zhou Q, Ding Y, Agostinho S, Kukelova Z, Sattler T, Leal-Taixé L.   +6 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Validating Single-Camera Pose Estimation Against Multi-Camera Motion Capture for Accessible Biomechanical Assessment. [PDF]

IEEE Access
Pratapneni A, Halvorson R, Silvestros P, Harris N, Bailey JF.   +4 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Robust Pose and Inertial Parameter Estimation of an Unknown Aircraft Based on Variational Bayesian Dual Vector Quaternion Extended Kalman Filter. [PDF]

Entropy (Basel)
Xu S, Fang Y, Huang H.
europepmc   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source