Results 21 to 30 of about 1,009,628 (283)

The Bauschinger effect in stainless steel orthodontic wires

open access: yesAustralasian Orthodontic Journal, 1987
The existence and clinical importance of the Bauschinger effect has received little attention in the orthodontic literature. Essentially, the Bauschinger effect describes the reduction in yield stress of a metal when the direction of defamation is ...
Gullotta Antonino   +2 more
doaj   +1 more source

Laser Micro Bending Process of Ti6Al4V Square Bar

open access: yesMicromachines, 2014
Laser micro bending process of Ti6Al4V square bar are carried out using a 3D thermo-mechanical finite element analytical model (FEM). The transient temperature fields, displacement fields, stress fields and strain fields are obtained and analyzed.
Gang Chen, Peng Zhang
doaj   +1 more source

Study on neutral layer offset of high-strength steel plate straightening of excavator’s working arm

open access: yesAdvances in Mechanical Engineering, 2017
The steel plate straightening quality has an important influence on the welding quality and service performance of excavator’s boom and arm. In this study, a stress neutral layer offset model was established based on three-point bending theory, steel ...
Qin-Hong Fan   +3 more
doaj   +1 more source

Measurement and Analysis of Root Anchorage Effect on Stalk Forces in Lodged Corn Harvesting

open access: yesFrontiers in Plant Science, 2022
The effect of root anchorage on corn stalk is the main cause of difficulties in stalk lifting and ear picking of lodged corn. To quantify the forces on the stalks caused by root anchorage in corn harvesting, a root force measurement system was designed ...
Qiankun Fu   +11 more
doaj   +1 more source

The effect of induced precipitations and pre-twins on the bending neutral layer migration behaviors of AZ80 Mg alloy sheet

open access: yesJournal of Materials Research and Technology, 2023
To explore the effect of the precipitated phase particles and twins on the microstructure evolution and neutral layer evolution during bending, {10–12} tensile twins were introduced along the transverse direction (TD) on AZ80 Mg alloy sheets at room ...
Zhen Zhang   +7 more
doaj   +1 more source

The nonlinear bending-torsion theory for curved rods as Gamma-limit of three-dimensional elasticity [PDF]

open access: yes, 2006
The problem of the rigorous derivation of one-dimensional models for nonlinearly elastic curved beams is studied in a variational setting. Considering different scalings of the three-dimensional energy and passing to the limit as the diameter of the beam
Scardia, L.
core   +6 more sources

Cellular mechanisms of reverse epithelial curvature in tissue morphogenesis

open access: yesFrontiers in Cell and Developmental Biology, 2022
Epithelial bending plays an essential role during the multiple stages of organogenesis and can be classified into two types: invagination and evagination.
Yiran Wang   +7 more
doaj   +1 more source

Fatigue analysis on flax-epoxy composites: insights and implications

open access: yesActa Polytechnica CTU Proceedings
This study investigates the performance of flax fiber and epoxy resin composites, focusing on fatigue testing, which is scarcely reported in the literature. Fatigue behavior is evaluated under full reverse bending loading conditions: R = −1.
Andrea Pagliaro, Lorenzo Cagnetta
doaj   +1 more source

Mrs. Montagu's contemplative bench: Bluestocking gardens and female retirement

open access: yes, 2006
Drawing on the correspondence of Elizabeth Montagu from the 1740s to the 1780s, Stephen Bending explores the role of gardens and retirement in the life of the leading eighteenth-century Bluestocking and argues that her estate at Sandleford played a ...
Bending, Stephen, Stephen Bending
core   +1 more source

Deformation Behavior of Reverse Deep Drawing of 5A06 Aluminum Alloy Plate

open access: yesCailiao gongcheng, 2017
The limit drawing ratio is influenced by the bending and unbending effect during reverse deep drawing of plate. The 5A06 aluminum alloy plate widely applied in aerospace industry was used, and the reverse deep drawing of the 4.5mm thick plate was ...
ZHANG Zhi-chao   +2 more
doaj   +1 more source

Home - About - Disclaimer - Privacy