Results 81 to 90 of about 4,944 (303)
Design, Testing and Validation of a Room Air Conditioner Test Facility
, 1994 "This report discusses the design, testing and validation of a room air conditioner test facility. The facility is designed to test the performance of air conditioners rated from 0.5 to 2.5 tons of refrigeration over a wide range of operating conditions.
Rugg, S.M.
core
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Simulation of Room Air Conditioner Performance
, 1995 "A room air conditioner simulation model has been developed, and validated experimentally. This report describes the assumptions made in the governing equations along with the process used to estimate a few empirical parameters, based on experimental ...
Bridges, B.D.
core
A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection
Advanced Engineering Materials, EarlyView.A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan +9 more
wiley +1 more source
Design of the Outdoor Environmental Chamber of a Room Air Conditioner Test Facility
, 1993 This document describes the design of the outdoor environmental chamber of a test facility for the collection of room air conditioner performance data over a wide range of psychrometric conditions.
Feller, S.D.
core
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
Seasonal Applicability of Refrigerant Release Technology in Room Air Conditioner
, 2014 The room air conditioner is widely used in residential and office buildings for both cooling and heating. However, the operation condition of the room air conditioner changes largely due to the variations of the cooling/heating load of the room, the ...
Wang, Baolong +3 more
core
Consumed by Abdominal Distention
Arthritis Care &Research, EarlyView.
Abimbola Fadairo‐Azinge +3 more
wiley +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source