Results 51 to 60 of about 295 (161)
Journal of Applied Crystallography, Volume 52, Issue 5, Page 1144-1156, October 2019., 2019 The single‐crystal elastic constants of polycrystalline titanium alloys have been determined using neutron and synchrotron powder diffraction.Single‐crystal elastic constants have been derived by lattice strain measurements using neutron diffraction on polycrystalline Ti‐6Al‐4V, Ti‐6Al‐2Sn‐4Zr‐6Mo and Ti‐3Al‐8V‐6Cr‐4Zr‐4Mo alloy samples.
Alexander Heldmann +8 more
wiley +1 more source
Fire Protection of Steel Beam by OSB Claddings—A Fire Experiment and Numerical Models
Fire and Materials, Volume 49, Issue 2, Page 196-214, March 2025.ABSTRACT This paper presents the results of a standard fire resistance test of a loaded steel beam in a horizontal furnace. The beam was tested in three configurations: (1) unprotected, (2) protected with a single 22 mm layer of oriented strand board, and (3) protected with a double layer of the same cladding.
Jakub Šejna +7 more
wiley +1 more source
Materialwissenschaft und Werkstofftechnik, Volume 50, Issue 8, Page 965-973, August 2019., 2019 Abstract The object of this investigation is to determine the influence of the jet velocity on the weld quality of sheet joints produced via magnetic pulse welding. The use of a suitable high‐speed camera system enables to observe the jet in detail, to determine its velocity during the collision process and to compare them to the achieved qualities ...
E. Schumacher, A. Rebensdorf, S. Böhm
wiley +1 more source
Analysis of the Strength of Assembly Joints - Welded Joints of Various Construction Materials
Technologia i Automatyzacja Montażu, 2023 The aim of the article was to present issues related to the strength analysis of one of the types of assembly joints -welded joints, taking into account the influence of selected factors: technological -welding method, construction -type of joints and ...
Anna Rudawska +4 more
doaj +1 more source
Toward Continuous Electrochemical Synthesis of Ferrate
Advanced Sustainable Systems, Volume 9, Issue 1, January 20, 2025.Ferrate synthesis using sacrificial iron anodes is studied at technical current densities. Anode passivation is overcome using spheroidal graphite cast iron as anode. A novel electrolysis cell allows the installation of rod‐shaped anodes with a combined surface area of 230 cm2.
Robin Kupec +7 more
wiley +1 more source
Multiphysics Model of an MR Damper including Magnetic Hysteresis
Shock and Vibration, Volume 2019, Issue 1, 2019., 2019 Hysteresis is one of key factors influencing the output of magnetorheological (MR) actuators. The actuators reveal two primary sources of hysteresis. The hydro(mechanical) hysteresis can be related to flow dynamics mechanisms and is frequency‐ or rate‐dependent.
M. Kubík +2 more
wiley +1 more source
Modelling the Damage of Structural Components with Macrostructure Defects
Metals, 2019 The article presents a numerical analysis of the process of damage of structural steel, the scope of which encompassed the estimation of the time to failure of a structural component.
Paweł Grzegorz Kossakowski
doaj +1 more source
Konya Journal of Engineering Sciences, 2019 In machining technologies, the most important criterion taken into consideration when evaluating the product quality is seen as the surface roughness. In the consideration of production quality and cost, tool wear is one of the factors that directly affect the cost of production.
Hasan Huseyin BILGIC +3 more
openaire +5 more sources
Energy Technology, Volume 13, Issue 1, January 2025.Material selection of tanks for storage and transport of a liquid organic hydrogen carrier is investigated. Three materials are compared: metals (steel), polymers (thermoplastic), and composites (glass fiber‐reinforced plastic). Criteria for selection relies on compliance to existing design standards, lightweight, and CO2 emissions.
Vinicius Carrillo Beber +2 more
wiley +1 more source
Structural Control and Health Monitoring, Volume 2025, Issue 1, 2025.This paper presents experimental testing of self‐diagnosis and self‐repair strategies on an adaptive truss prototype that counteracts the effect of loading through shape morphing. The prototype is a simply supported spatial truss with a span of 6 m and is equipped with 12 linear actuators.
Arka P. Reksowardojo +4 more
wiley +1 more source