Results 61 to 70 of about 295 (161)
High-hardness and corrosion-resistant Ni-hard overlays on S235JR steel via GTAW process
Discover Applied SciencesEquipment used in mining, agriculture, and machining frequently fails due to simultaneous wear and corrosion, which shortens service life and increases maintenance costs.
Farhad Ostovan +3 more
doaj +1 more source
Technologia i Automatyzacja Montażu, 2021 The aim of the work was to investigate the influence of the directivity of the geometric structure obtained in the grinding process on the load capacity of single-lap adhesive joints made of steel S235JR and aluminum alloy 2024-T3.
Władysław Zielecki +2 more
doaj +1 more source
Non‐destructive evaluations of water uptake in epoxy coating
Journal of Applied Polymer Science, Volume 141, Issue 2, January 10, 2024.Techniques for non‐destructive evaluation of water uptake in epoxy coating. Abstract A commercial epoxy coating was studied on steel panels and as free films to investigate water uptake using non‐destructive techniques (gravimetric analysis, Electrochemical Impedance Spectroscopy [EIS], Attenuated Total Reflection‐Fourier Transform Infrared ...
Shu Li +3 more
wiley +1 more source
Effect of Welding Sequence in Angular Distortion on Butt Joint GMAW Process
Applied Sciences, 2022 Over time, the industrial use of the welding process has grown in significance and is now one of the primary methods for joining metallic parts. During the welding process, metallurgical and structural modifications occur close to the welded joint.
Inês S. Afonso +2 more
doaj +1 more source
OPTIMIZING TENSILE STRENGTH AT MAG WELDING PROCESS OF S235JR STEEL
ENVIRONMENT. TECHNOLOGY. RESOURCES. Proceedings of the International Scientific and Practical ConferenceThe article is of an experimental nature for welding S235JR by MAG welding method. The purpose of this work is to optimize the welding parameters of MAG welding using shield two-component gas cargon 18 to achieve ultimate tensile strength. The experiment is according to central composition design and 13 experiments were made. Samples with dimensions of
Sabev, Sabi, Chukalov, Konstantin
openaire +2 more sources
Acta Technologica Agriculturae, 2019 Presented paper deals with the issue of lubricating tribological systems formed by a double pair operating under mixed conditions of mixed friction before and after experimental tests, which were conducted in accordance with the selected methodology ...
Tóth František +4 more
doaj +1 more source
MATEC Web of Conferences, 2018 Studies show that although commonly used steels are standardized, some of their mechanical properties (such as tensile strength) vary widely and knowledge of their corrosion behavior is insufficient.
Tsonev Veselin +2 more
doaj +1 more source
Research in Agricultural Engineering, 2011 Automatic weld surfacing is being employed increasingly in the process, mining and power industries. Gas metal arc welding has become a natural choice for automatic surfacing due to its important properties. These include: high reliability, all positions
R. Chotěborský +2 more
doaj +1 more source
Abrasive wear of high chromium Fe-Cr-C hardfacing alloys
Research in Agricultural Engineering, 2008 Weld deposits are one of the most used economical ways of the wear resistance increase. The study compares the characteristics of the overlay material welded-on and the abrasive wear resistance.
R. Chotěborský +4 more
doaj +1 more source
Examination of weld defects by computed tomography
Metalurgija, 2012 Defects in metal arc gas (MAG) welds made in S235JR low carbon steel of 6 mm thickness were examined. A sample containing lack of fusion (LOF) and pores was examined by computed tomography – CT.
M. Jovanović, L. Kosec, B. Zorc
doaj