Results 191 to 200 of about 13,503 (304)

A Randomized Controlled Trial Assessing Full-Mouth Versus Quadrant-Based Scaling and Root Planing for Non-surgical Periodontal Therapy. [PDF]

Cureus
Gaddam D, Nagarakanti S, Sravya Sri P, Chiruvella B, R R, Gudur T.   +5 more
europepmc   +1 more source

Deterministic Detection of Single Ion Implantation

Advanced Engineering Materials, EarlyView.
Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead, Lok Kan Wan, Maddison Coke, Janet Jacobs, Nicholas F. L. Collins, Mark C. Rosamond, Richard J. Curry   +6 more
wiley   +1 more source

Assessment of Low Level Laser Therapy on Periodontal Inflammation and Healing after Scaling and Root Planing in Chronic Periodontitis Patients - A Clinico Biochemical Study. [PDF]

J Pharm Bioallied Sci
Soni R, Sharma M, Tabassum, Singh R, Yadav BK, Thakur RK.   +5 more
europepmc   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Clinical Comparison of Guided Biofilm Therapy and Scaling and Root Planing in the Active Phase of Periodontitis Management. [PDF]

Eur J Dent
Mensi M, Sordillo A, Marchetti S, Calza S, Scotti E.   +4 more
europepmc   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Impact of Pre‐Oxidation Treatments on a Recycled MgO/Steel‐Composite as Carbon Free Anode in Aluminum‐Electrolysis Environments

Advanced Engineering Materials, EarlyView.
Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser, Felix Drechsler, Nora Brachhold, Florian Kerber, Christos G. Aneziris   +4 more
wiley   +1 more source

Evaluation of locally delivered biodegradable cefixime strips as an adjunct to scaling and root planing in chronic periodontitis: A clinical study.

J Indian Soc Periodontol
Vediya SS, Jain P, Shetty N, Mathur A, Bali A.   +4 more
europepmc   +1 more source

Laser Therapy Versus Traditional Scaling and Root Planing: A Comparative Review. [PDF]

Cureus
Altalhi AM, AlNajdi LN, Al-Harbi SG, Aldohailan AM, Al-Ghadeer JY, Al-Bahrani JI, Al-Gahnem ZJ, Alenezi AH, Al-Majid A.   +8 more
europepmc   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source