Results 161 to 170 of about 362,376 (266)

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Exploring partially reduced CeO   2 (111) surface at the atomic scale using scanning probe microscopy. [PDF]

Sci Technol Adv Mater
Kim K, Abe M, Kawai S, Custance O.
europepmc   +1 more source

Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC

Advanced Engineering Materials, EarlyView.
ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko, Evelyn Wang, Michael A. Hickner   +2 more
wiley   +1 more source

Design of an FPGA-Based Controller for Fast Scanning Probe Microscopy. [PDF]

Sensors (Basel)
Gregorat L, Cautero M, Carrato S, Giuressi D, Panighel M, Cautero G, Esch F.   +6 more
europepmc   +1 more source

Scanning Probe Microscopy Bone Marrow Determination of Steogenic Differentiation of Mesenchymal Stem Cells.

Contrast Media Mol Imaging, 2022
Fu X, Lian Q, Zhang B, Teng X, Chen Y, Qu Y, Cheng Z, Guo L.   +7 more
europepmc   +1 more source

Scanning probe microscopy

Scanning probe microscopy
identifier:oai:t2r2.star.titech.ac.jp ...
openaire  

Investigation of Thermo‐Chemical Processes in Commercial MgO‐C Refractory Bricks With and Without MgO‐C Recyclate at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm, Jana Hubálková, Christian Schimpf, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +6 more
wiley   +1 more source

Recent advances in characterization of rechargeable battery materials <i>via</i> scanning probe microscopy. [PDF]

J Mater Chem A Mater
Russell JA, Davis PH, Efaw CM, Xiong H.
europepmc   +1 more source

Multi-Channel Exploration of O Adatom on TiO₂(110) Surface by Scanning Probe Microscopy. [PDF]

Nanomaterials (Basel), 2020
Wen HF, Sugawara Y, Li YJ.
europepmc   +1 more source

Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio

Advanced Engineering Materials, EarlyView.
This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov, Matheus Roberto Bellé, Anton Yehorov, Julia Richter, Olena Volkova   +4 more
wiley   +1 more source