Results 71 to 80 of about 2,944 (263)
Nuclear Materials and EnergyUEDGE simulations with density scans for various input power, transport coefficients and outer poloidal leg length are performed to study the conditions for the existence of a bifurcation-like drop of Te at the outer strike point, commonly referred to as
M. Zhao +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Inferring the scrape-off layer heat flux width in a divertor with a low degree of axisymmetry
Nuclear Materials and EnergyPlasma facing components (PFCs) in the next generation of tokamak devices will operate in challenging environments, with heat loads predicted to exceed 10 MW/m2. The magnitude of these heat loads is set by the width of the channel, the ‘scrape-off layer’
C. Marsden +8 more
doaj +1 more source
Nuclear Materials and Energy, 2017 The understanding of divertor physics and the evolution of divertor detachment is crucial for developing the capability to model power exhaust in current experiments and reliably predict it for future fusion devices.
F. Reimold +7 more
doaj +1 more source
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
Nuclear FusionThe EMC3-Eirene code was used to study the main impurity leakage mechanism for the island divertor in the standard magnetic field configuration. It was found that under experimentally accessible plasma scenarios in the last experimental campaign, the ...
V.R. Winters +14 more
doaj +1 more source
From Food to Power: Hydrogel Thermoelectrics for Ingestible Electronics
Advanced Functional Materials, EarlyView.We introduce a fully edible thermoelectric–electrochromic platform that harvests heat from food and converts it into a visible color change. N‐type and p‐type hydrogel thermoelectric generators connected in series power anthocyanin‐based electrochromic displays, demonstrating the feasibility of safe, biodegradable, ingestible systems for on‐food ...
Antonia Georgopoulou +3 more
wiley +1 more source
Advanced Functional Materials, EarlyView.In MOCVD MoS2 memristors, a current compliance‐regulated Ag filament mechanism is revealed. The filament ruptures spontaneously during volatile switching, while subsequent growth proceeds vertically through the MoS2 layers and then laterally along the van der Waals gaps during nonvolatile switching.
Yuan Fa +19 more
wiley +1 more source
Advanced Functional Materials, EarlyView.ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo +10 more
wiley +1 more source
Influence of plasma background including neutrals on scrape-off layer filaments using 3D simulations
Nuclear Materials and Energy, 2017 This paper investigates the effect of the plasma background, including neutrals in a self-consistent way, on filaments in the scrape-off layer (SOL) of fusion devices.
D. Schwörer +6 more
doaj +1 more source