Results 81 to 90 of about 3,889,999 (300)
Formation of Quasi‐Decoupling Interface on Li‐Metal Anodes in High Donor Electrolyte
Advanced Functional Materials, EarlyView.Li‐metal anode (LMA) is stabilized by introducing Li2Te2 as an electrolyte additive for Li‐metal batteries. Upon contact with Li, Li2Te2 spontaneously converts to Li2Te, which electronically isolates Li from dimethyl sulfoxide due to its large bandgap and minimal Bader charge transfer.
Hyerim Kim +9 more
wiley +1 more source
Patient Preference and Adherence, 2023 Alan Kivitz,1 Alicia M Ellis,2 Vishvesh Shende,3 Jérémy Lambert,4 Daljit Tatla2 1Altoona Center for Clinical Research, Duncansville, PA, USA; 2UCB Pharma, Raleigh, NC, USA; 3UCB Pharma, Slough, UK; 4UCB Pharma, Colombes, FranceCorrespondence: Daljit ...
Kivitz A +4 more
doaj
Intravenous self-injection of methcathinone in the baboon
Pharmacology Biochemistry and Behavior, 1994 Methcathinone is a phenylisopropylamine that has been produced by clandestine laboratories and identified in illicit drug traffic. The present study evaluated the intravenous self-administration of methcathinone in three baboons using a cocaine substitution procedure.
B J, Kaminski, R R, Griffiths
openaire +2 more sources
Self‐Healing and Stretchable Synaptic Transistor
Advanced Functional Materials, EarlyView.A self‐healing stretchable synaptic transistor (3S‐T) is realized using a p‐PVDF‐HFP‐DBP/PDMS‐MPU‐IU bilayer as gate insulator, where dipole‐dipole interaction enhances polarization to achieve a large memory window. Leveraging its neuronal biomimicry, the synaptic transistor demonstrates electrically compatibility with the biological brain. Furthermore,
Hyongsuk Choo +10 more
wiley +1 more source
CAE for Advanced Injection Molding Technologies
, 2019 Injection molding is one of the most popular polymer processing methods and has been used to mass produce plastics products for many decades. However, due to increasingly stringent requirements and higher customer expectations, conventional injection ...
Chang, Rong-Yeu;Huang, Chao-Tsai (CT)
core +1 more source
Advanced Functional Materials, EarlyView.A fluorine‐rich acrylate monomer (PFHEA) was solvent‐free applied to NCM90 and thermally decomposed under Ar to convert residual lithium into LiF and form a pre‐built LiF/fluorinated amorphous carbon (LiF/FC) interphase. The LiF/FC layer suppresses NiO rock‐salt reconstruction and microcrack propagation, lowers interfacial resistance, and improves Li ...
Pangyu Kim +6 more
wiley +1 more source
Development of devices for self-injection: using tribological analysis to optimize injection force
, 2016 Jakob Lange, Leos Urbanek, Stefan BurrenYpsomed Delivery Systems, Ypsomed AG, Burgdorf, Switzerland Abstract: This article describes the use of analytical models and physical measurements to characterize and optimize the tribological behavior ...
Urbanek L, Burren S, Lange J
core
Evidence and information for national injection safety policies [PDF]
, 2003 The adverse consequences of poor injection practices have been reported for a few decades. However, key elements of evidence and information were lacking to allow decision-makers to formulate policies for the safe and appropriate use of injections.
Hutin, Yvan
core +1 more source
Advanced Functional Materials, EarlyView.ABSTRACT Traditional wearable exoskeletons rely on rigid structures, which limit comfort, flexibility, and everyday usability. This work introduces the fundamental technologies to create the first soft, lightweight, intelligent textile‐based exoskeletons (Texoskeletons) built using 1D sensors and actuators.
Amy Lukomiak +19 more
wiley +1 more source
, 2006 Previous examinations of relations between bullying, victimisation, and self-concept have been flawed by erroneous research practices such as the un-attenuated use of dichotomous variables to measure relationships between continuous variables (Finger ...
Finger, Linda R. +2 more
core