Results 51 to 60 of about 79,002 (263)

Visualization of the Equilibrium FCC Catalyst Surface by AFM and SEM–EDS [PDF]

Catalysis Letters, 2003
The deposition of metal contaminants (e.g., Ni, V, and Fe) from the hydrocarbon feed causes the deactivation of fluid catalytic cracking (FCC) catalyst used in petroleum refining. It is very important to understand the changes in the morphology and chemical composition on the catalyst surface and how these structural and chemical changes affect the ...
Bayraktar, Oğuz, Kugler, Edwin L.
openaire   +2 more sources

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

The SEM/EDS analysis of zeolite minerals

, 2021
The SEM/EDS analysis is one of the most important methods for characterizing and determining the morphology of minerals.In scanning electron microscopy (SEM), a highly energetic and focused electron beam scans the sample and normally provides an extremely enlarged image of the morphology of the sample, as well as information on its chemical composition
Mitić, Vojislav V., Mihajlović, Katarina, Kosić, I, Arsenijević, D., Kašić, Vladan   +4 more
openaire   +1 more source

A SEM, EDS and vibrational spectroscopic study of the clay mineral fraipontite [PDF]

Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, 2015
The mineral fraipontite has been studied by using a combination of scanning electron microscopy with energy dispersive analysis and vibrational spectroscopy (infrared and Raman). Fraipontite is a member of the 1:1 clay minerals of the kaolinite-serpentine group. The mineral contains Zn and Cu and is of formula (Cu,Zn,Al)₃(Si,Al)₂O₅(OH)₄.
Theiss, Frederick, Lopez Toro, Andres, Scholz, Ricardo, Frost, Ray   +3 more
openaire   +3 more sources

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source

Stiren-Bütadien Kopolimer Katkısının Çimento Harçlarına Etkisi

Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2016
Beton üretiminde çoğunlukla yeni kuşak kimyasal katkılar kullanılmaktadır. Dağıtma (dispersiyon) gücü yüksek olan kimyasal katkıların beton içerisinde belirli oranlarda kullanılması esastır.
Alper Bideci, Murat Doğan, Bekir Çomak, Özlem Sallı Bideci, Elif Besli   +4 more
doaj  

On the Effect of Creep on Local Lattice Orientation in Single‐Crystal Ni‐Based Superalloy Microstructures

Advanced Engineering Materials, EarlyView.
During creep of a single‐crystal Ni‐based superalloy, the overall crystal orientation is observed to remain constant while the microstructure evolves. Despite the lack of macroscopic rotation, small (<1°) rotations are observed on the submicron size scale and are accommodated by counteracting rotations over the scale of several micrometers.
E. J. Payton, E. B. Dursun, G. Eggeler, L. Agudo Jácome   +3 more
wiley   +1 more source