Results 121 to 130 of about 4,665 (266)
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects
Advanced Engineering Materials, EarlyView.This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Evaluation of Sensible Heat Flux and Evapotranspiration Estimates Using a Surface Layer Scintillometer and a Large Weighing Lysimeter. [PDF]
Sensors (Basel), 2017 Moorhead JE +7 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe +4 more
wiley +1 more source
Gravity wave heating and cooling of the thermosphere: Sensible heat flux and viscous flux of kinetic energy [PDF]
Journal of Geophysical Research: Space Physics, 2011 M. P. Hickey +2 more
openaire +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Water Resources ResearchUnderstanding how the net Solar radiation is partitioned into heat fluxes on land surface is fundamental to understand water, energy, and carbon cycles. Here we claim that, in forests under energy‐limited environment, the proportion in the net radiation ...
Kwanghun Choi, Kyungrock Paik
doaj +1 more source
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source