Results 31 to 40 of about 1,439 (167)
steel research international, EarlyView.Laser powder bed fusion of JIS SKD61 tool steel is systematically optimized using a Taguchi design and ANOVA. Hatch spacing and layer thickness are identified as dominant parameters controlling surface roughness and tensile strength. Subsequent tempering at 600°C improves microstructural stability and mechanical performance, enabling high‐density SKD61
Masrurotin Masrurotin +4 more
wiley +1 more source
steel research international, EarlyView.The article explores how high‐strength steels and press hardening revolutionize lightweight chassis design for heavy‐duty vehicles. It reveals that press hardened steels combined with shot peening can cut weight by up to 34% and reduce environmental impact by 21%–32%.
Violeta Vargas‐Parra +7 more
wiley +1 more source
Journal of Biomedical Materials Research Part B: Applied Biomaterials, Volume 114, Issue 8, August 2026.ABSTRACT Despite the success of total knee arthroplasty (TKA), a small percentage of devices fail. Due to the high volume of surgeries performed each year, revision total knee arthroplasty surgery presents a burden on patients and surgeons. One aspect that may improve TKA outcomes is device design, specifically the use of grit blasting to increase the ...
Peter W. Kurtz +8 more
wiley +1 more source
steel research international, Volume 97, Issue 8, Page 4326-4336, August 2026.Surface reconditioning through mechanical and electrochemical polishing is shown to extend the fatigue life of predamaged 42CrMo4 steel by over 12 times. By removing ≈100 μm of surface material, surface‐driven fatigue damage is mitigated. This study introduces a reuse potential metric to evaluate fatigue recovery and support sustainable steel reuse. To
Ayush Shrivastava +7 more
wiley +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, Volume 28, Issue 14, 22 July 2026.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
Method of Inverse Modeling for Tailored Residual Stress Depth Profiles After Deep Rolling
Engineering Reports, Volume 8, Issue 7, July 2026.In this paper, a modified sinusoidal decay function was used to model residual stress depth profiles based on the determined coefficients and a regression analysis. This model can be used to predict residual stress depth profiles after deep rolling. ABSTRACT This paper lays the foundation for an inverse model to achieve tailored residual stress depth ...
Vannila Prasanthan +4 more
wiley +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Rejuvenated Amorphous Alloys: Processing Methods, Microstructures and Mechanical Properties
Advanced Science, Volume 13, Issue 33, 15 June 2026.Three rejuvenation methods – mechanical and thermal rejuvenation, and other rejuvenation routes such as ultrasonic processing – can be used to modify structures of glassy alloys, especially atomic clusters, and therefore enhances plasticity and activates work‐hardening behaviors.
Can Yang +10 more
wiley +1 more source
High Cycle Fatigue Properties of PM‐HIPed High‐Nitrogen Tool Steel: Effect of Surface Condition
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 6, Page 2097-2115, June 2026.ABSTRACT This study explores the impact of surface condition on high‐cycle fatigue performance of a high‐nitrogen martensitic tool steel manufactured through powder metallurgy and hot isostatic pressing. In near‐net manufacturing applications, acid‐leaching pickling treatment and/or machining is used as a post‐treatment to remove the powder container ...
Faezeh Javadzadeh Kalahroudi +3 more
wiley +1 more source
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 6, Page 2352-2362, June 2026.ABSTRACT The milling process significantly influences the surface integrity of metallic components through machining induced near‐surface residual stresses. Modern hybrid machining processes, such as ultrasonic‐assisted milling (USAM), offer the potential to induce beneficial near‐surface compressive residual stresses compared to the near‐surface ...
Lorenz Engelking +5 more
wiley +1 more source