Results 41 to 50 of about 308,390 (162)

Measurement of shot velocity using particle image velocimetry and numerical analysis of residual stress at two shot peening conditions

Mechanical Engineering Journal, 2020
Shot peening is applied to many manufactured parts to improve the fatigue strength of metals by introducing compressive residual stress near the surface. The distribution of compressive residual stress is mainly determined by shot diameter, shot velocity,
Takahiro OHTA, Ninshu MA
doaj   +1 more source

In Situ Rare Earth Nanoparticle Reinforcement of NiCoCrAlYTa Coatings via HCPEB Modification: Insights Into Early Oxidation Behavior and Microstructural Evolution

Rare Metals, Volume 45, Issue 9, September 2026.
ABSTRACT NiCoCrAlYTa coatings are widely used as bond coats in thermal barrier coating (TBC) systems for gas turbines and aeroengines to provide oxidation resistance and support the formation of a protective thermally grown oxide (TGO). Herein, high‐current pulsed electron beam (HCPEB) modification was utilized to strengthen a NiCoCrAlYTa coating by ...
Xiangcheng Li, Wei Qian, Xiaofeng Zhang, Bin Gan, Xiang Xu, Jie Cai, Jinzhong Lu   +6 more
wiley   +1 more source

Evaluation of rolling contact fatigue behaviour of bearing steel subjected to shot peening in a contaminated lubrication

Nihon Kikai Gakkai ronbunshu, 2017
In this study, the effect of shot peening on rolling contact fatigue life of bearing steel was investigated under contaminated lubrication. Shot peening was carried out on bearing steel SUJ2 specimens. Peened specimens were polished to remove the dimples
Tomoya SADAMORI, Koji TAKAHASHI, Hitonobu KOIKE   +2 more
doaj   +1 more source

Residual Al2O3 From Grit Blasted Components Operate as Third Body Wear Particles in Total Knee Arthroplasty: An Exploratory Study

Journal of Biomedical Materials Research Part B: Applied Biomaterials, Volume 114, Issue 8, August 2026.
ABSTRACT Despite the success of total knee arthroplasty (TKA), a small percentage of devices fail. Due to the high volume of surgeries performed each year, revision total knee arthroplasty surgery presents a burden on patients and surgeons. One aspect that may improve TKA outcomes is device design, specifically the use of grit blasting to increase the ...
Peter W. Kurtz, Bradley Gordon, Charley M. Goodwin, Emma Barnes, Dinghe Liu, Steven M. Kurtz, Nicolas S. Piuzzi, William M. Mihalko, Jeremy L. Gilbert   +8 more
wiley   +1 more source

In Situ Acoustic Monitoring of Focused Femtosecond Pulse Duration in Air

Laser &Photonics Reviews, Volume 20, Issue 16, 21 August 2026.
Air‐breakdown acoustics at the laser focus is used to determine femtosecond pulse duration with a simple USB microphone. By chirp‐tuning and compressing 1030 nm pulses from 241 to 50 fs, the acoustic amplitude scales inversely proportional to the square root of the pulse duration, enabling in situ readout over 50 fs–5 ps—crucial for precise pulse ...
Indrė Meškėlaitė, Hsin‐Hui Huang, Haoran Mu, Nguyen Hoai An Le, Tomas Katkus, Edvinas Aleksandravičius, Gabrielius Kontenis, Domas Paipulas, Saulius Juodkazis, Darius Gailevičius   +9 more
wiley   +1 more source

Increasing the Reuse Potential of High‐Strength Steels by Extending the Fatigue Life through Surface Treatments

steel research international, Volume 97, Issue 8, Page 4326-4336, August 2026.
Surface reconditioning through mechanical and electrochemical polishing is shown to extend the fatigue life of predamaged 42CrMo4 steel by over 12 times. By removing ≈100 μm of surface material, surface‐driven fatigue damage is mitigated. This study introduces a reuse potential metric to evaluate fatigue recovery and support sustainable steel reuse. To
Ayush Shrivastava, Oguz Gulbay, Srinivasa Raghavan Raghuraman, Marion Kreins, Fabian Weber, Peter Starke, Alexander Gramlich, Ulrich Krupp   +7 more
wiley   +1 more source

Local Fatigue Strength Evaluation of Shot Peened 40Cr Notched Steel

Metals, 2018
Fatigue life prediction for the notched components is an essential step within the design process of machines. Fatigue strength and life prediction of 40Cr notched steel before and after shot peening were studied. Fatigue fracture of specimens treated by
Xiaohui Zhao, Zhaoyi Sun, Desheng Xu, Yu Liu   +3 more
doaj   +1 more source

Influence of Shot Peening on the Wear Behaviour of Medium Carbon Steel

Production Engineering Archives, 2022
Influence of shot peening on the wear behaviour of medium carbon, C55 steel was experimentally verified. Experimental work included determination of the chemical composition, heat treatment, microstructure evaluation, mechanical properties measurement ...
Vicen Martin, Bokůvka Otakar, Trško Libor, Drbul Mário, Nikolić Ružica, Nový František   +5 more
doaj   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, Volume 28, Issue 14, 22 July 2026.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Finite element modelling of shot peening process- A progress overview [PDF]

International Journal for Simulation and Multidisciplinary Design Optimization, 2009
It is very significant to investigate the shot peening mechanism in ensuring a good resistance to fatigue and stress corrosion. This paper reviews the recent advancements in shot peening process. Emphasis is put on the application of numerical simulation
Yang Y. H., Wan M., Zhang W. H.
doaj   +1 more source