Results 181 to 190 of about 19,399 (314)

Flood Algorithm-Tuned PID-F Controller with a Modified Objective Function for Robust and Noise-resilient Speed Control of Nonlinear SparkIgnition Engines. [PDF]

Sci Rep
Ekinci S, Izci D, Turkeri C, Bajaj M, Rubanenko O.   +4 more
europepmc   +1 more source

Numerical analysis of combustion and transient heat transfer processes in a two-stroke SI engine

, 2010
Fernando Illán Gómez, M. Alarcón
openalex   +2 more sources

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

CFD-enabled sustainable design and manufacturing of cooling fan for unmanned helicopter. [PDF]

Sci Rep
Si L, Liu Z, Xiao N, Zhang Y, Liu Y, Deng S, Li Y, Yang H, Zhang X, Fu G, Choi JP.   +10 more
europepmc   +1 more source

Artificial intelligence based emission and performance prediction, and optimization of HHO-blended gasoline SI engine: A sustainable transition

Muhammad Nasir Bashir, Muhammad Usman, Fahid Riaz, Touqeer Ahmad, Yasser Fouad, M. Shameer Basha, M.A. Mujtaba, Joon Sang Lee   +7 more
openalex   +1 more source

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Enhancing atomization and spray patterns of spray G in a gasoline direct injection system using biofuel blends with gasoline. [PDF]

Sci Rep
Pawar JU, Saraf AK, Singh MP, Goyal R.
europepmc   +1 more source

Performance of a Printed Bimetallic (Stainless Steel and Bronze) Engine Head Operating under Stoichiometric and Lean Spark Ignited (SI) Combustion of Natural Gas

, 2020
Michael D. Kass, Munidhar Biruduganti, Brian Kaul, John M. E. Storey, Douglas E. Longman, Amelia Elliott, Derek Siddel   +6 more
openalex   +2 more sources

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source