Results 41 to 50 of about 2,384 (206)
Increase of a Fatigue Life of a Silumin by Electron-Beam Processing
Успехи физики металлов, 2015 At present, the aluminium-alloy productions become increasingly popular in different branches of industry. However, the relatively low strength properties of silumin significantly restrict its scope of application.
V. E. Gromov, K. V. Aksyonova, S. V. Konovalov, Yu. F. Ivanov
doaj +1 more source
Archives of Foundry Engineering, 2023 Final quality of casts produced in a die casting process represents a correlation of setting of technological parameters of die casting cycle, properties of alloy, construction of a die and structure of gating and of bleeding systems.
J. Majernik, S. Gaspar
semanticscholar +1 more source
IMPROVEMENT OF SECONDARY SILUMIN AK12M2MGH BY NANO-MODIFICATION
Innovative Materials and Technologies in Metallurgy and Mechanical Engineering, 2023 Мітяєв О. А. д-р техн. наук, професор, завідувач кафедри композиційних матеріалів, хімії та технологій Національного університету «Запорізька політехніка», м. Запоріжжя, Україна, e-mail: mityaev@zp.edu.ua; Волчок І. П. д-р техн.
О. Mityaev +4 more
semanticscholar +1 more source
RESEARCH AND IMPROVEMENT OF THE MECHANICAL PROPERTIES OF SILUMIN AK7ч
New Materials and Technologies in Metallurgy and Mechanical Engineering, 2023 Purpose. Research and improvement of the technology of improving the quality of secondary silumins developed by Zaporizhzhya Polytechnic National University.
O. Petrashov +4 more
semanticscholar +1 more source
British journal of multidisciplinary and advanced studies, 2022 The management of waste products may reduce pollution and dumping sites. Therefore, one of the main goals of contemporary research is to recover these wastes through conversion into a more environmentally acceptable material that applies to fabrication ...
O. O. Barah
semanticscholar +1 more source
THE PROBLEM OF MODIFYING AN ALUMINUM-SILICON EUTECTIC ALLOY OF SILUMINS. WAY OF SOLUTIONS
Литьë и металлургия, 2018 It is shown that modern industrial modifiers of silumin eutectic contribute to the saturation of the melt with hydrogen. Its micro bubbles block the branching of eutectic crystals and promote the formation of gas porosity in castings.To improve the ...
E. I. Marukovich,, V. Yu. Stetsenko
doaj +1 more source
Успехи физики металлов, 2019 The structural-phase states, microhardness, and tribological properties of hypoeutectic silumin after electron-beam treatment are studied by the methods of contemporary physical materials science.
Yu. F. Ivanov, V. E. Gromov, D. V. Zagulyaev, S. V. Konovalov, Yu. A. Rubannikova, A. P. Semin
doaj +1 more source
Inorganic Materials: Applied Research, 2022 The effects of high-energy compression plasma flows on the structure, elemental composition, and phase state of Al–44 at % Si hypereutectic silumin alloy have been investigated.
V. I. Shymanski +7 more
semanticscholar +1 more source
Archives of Metallurgy and Materials, 2017 The paper presents a research on the effect of extreme - for the technology of the considered silumin EN AB 47100 - parameters of high-pressure die casting on occurrence of casting nonconformities.
Pałyga Ł., Stachowicz M., Granat K.
doaj +1 more source
RESEARCH OF THE TRIBOLOGICAL PROPERTIES OF CAST SILUMIN АК15М3
Литьë и металлургия, 2018 A comparative study of the tribological properties of antifriction silumin casting АК15М3 and typical bronzes БрОЦС, БрОФ and БрАЖ at the friction in the lubricant-20A in a wide range of sliding velocities and pressures of the tests.
E. I. Marukovich +4 more
doaj +1 more source