Results 81 to 90 of about 4,649,771 (242)

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Elastic Properties and Thermal Expansion Behavior of a Polycrystalline VMnFeCoNi High‐Entropy Alloy

Advanced Engineering Materials, EarlyView.
The high‐entropy alloy (HEA) V20Mn20Fe20Co20Ni20 (composition in at.%) can be made single‐phase face‐centered cubic (FCC) when annealed above 1338 K followed by water quenching. In this state, the alloy exhibits the greatest strength‐ductility combination of any quinary single‐phase FCC HEA.
Guillaume Laplanche, Marie Münchhalfen, Aditya Srinivasan Tirunilai, Jürgen Schreuer   +3 more
wiley   +1 more source

A Stochastic source model for the 2015 Mw 7.9 Gorkha, Nepal, Earthquake using Multi-Dimensional Ensemble Empirical Mode Decomposition technique

MATEC Web of Conferences, 2018
The present study aims at developing a new strategy to model the spatial variability of slip on the rupture plane using multi-dimensional ensemble empirical mode decomposition (MEEMD) technique. Here, the earthquake slip distribution is split into finite
Sangeetha S, Raghukanth S.T.G
doaj   +1 more source

Distinct Microstructural Characteristic Lengths Defining Notch Fatigue Crack Initiation and Propagation, and Defect Tolerance in Advanced Steels

Advanced Engineering Materials, EarlyView.
Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley   +1 more source

Simulation of the flow and the study of the effects of the surface roughness in isothermal gas flows of micro scale using Lattice Boltzmann method [PDF]

, 2009
This paper was presented at the 2nd Micro and Nano Flows Conference (MNF2009), which was held at Brunel University, West London, UK. The conference was organised by Brunel University and supported by the Institution of Mechanical Engineers, IPEM, the ...
2nd Micro and Nano Flows Conference (MNF2009), Tamaddon, H, Raisee, M   +2 more
core   +5 more sources

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Tsunami Induced by the Strike‐Slip Fault of the 2018 Palu Earthquake (Mw = 7.5), Sulawesi Island, Indonesia

Earth and Space Science, 2021
An unusual devastating tsunami occurred on September 28, 2018 after a strike‐slip faulting earthquake in Sulawesi, Indonesia. The induced tsunami struck Palu city with ∼4‐m flow depth.
Tung‐Cheng Ho, Kenji Satake, Shingo Watada, Ming‐Che Hsieh, Ray Y. Chuang, Yosuke Aoki, Iyan E. Mulia, Aditya Riadi Gusman, Chih‐Heng Lu   +8 more
doaj   +1 more source

Change in drag, apparent slip and optimum air layer thickness for laminar flow over an idealised superhydrophobic surface [PDF]

, 2013
Analytic results are derived for the apparent slip length, the change in drag and the optimum air layer thickness of laminar channel and pipe flow over an idealised superhydrophobic surface, i.e. a gas layer of constant thickness retained on a wall.
Newton, M.I., Busse, A., McHale, G., McHale, Glen, Sandham, Neil D., Busse, Angela, Newton, Michael, Newton, Michael I., Sandham, N., Sandham, Neil   +9 more
core   +1 more source

Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring

Advanced Engineering Materials, EarlyView.
Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak, Yasmina Frey, Ulrike Wallrabe, Oswald Prucker, Jürgen Rühe   +4 more
wiley   +1 more source

Discrepancies Between Micro Versus Macroscale Viscoelastic Properties in a Microplastic‐Tissue Composite Model

Advanced Engineering Materials, EarlyView.
This study explores the discrepancies between bulk mechanics and spatial mapping in a tissue‐mimetic hydrogel model. Microplastic particles create localized stiff mechanical microenvironments that are detectable by cellular‐scale nanoindentation but leave bulk properties unchanged as measured by rheology.
Ahron T. Verschleisser, Baptiste Le Roi, Omri Leshem, Joshua M. Grolman   +3 more
wiley   +1 more source