Results 51 to 60 of about 13,395 (247)
Advanced Functional Materials, EarlyView.This work presents a rate‐adaptive site transformation strategy in Ag‑ethylenediamine intercalated Co9S8, which not only enables parallel water dissociation and H* adsorption, but also allows the catalyst to provide more active sites under high demand, removing a major bottleneck. The catalyst achieves a record current density of 4.2 A cm−2@2.0 V, with
Yongqi Ye +3 more
wiley +1 more source
Structural and Luminescence Properties of SnO2 Nanostructures Via Porcine Gelatin-Assisted Synthesis
Iranian Journal of Materials Science and Engineering, 2021 Porous nanostructured SnO2 with a sheet-like morphology was synthesized through a simple green substrate-free gelatin-assisted calcination process using Tin tetracholoride pentahydrate as the SnO2 precursor and porcine gelatin as the template ...
Arian Heidar Alaghband +3 more
doaj
Atomic Layer Deposition in Transistors and Monolithic 3D Integration
Advanced Functional Materials, EarlyView.Transistors are fundamental building blocks of modern electronics. This review summarizes recent progress in atomic layer deposition (ALD) for the synthesis of two‐dimensional (2D) metal oxides and transition‐metal dichalcogenides (TMDCs), with particular emphasis on their enabling role in monolithic three‐dimensional (M3D) integration for next ...
Yue Liu +5 more
wiley +1 more source
SnO2–Bi2O3 and SnO2–Sb2O3 gas sensors obtained by soft chemical method
Journal of the European Ceramic Society, 2007 Abstract In this work, SnO2–Bi2O3 and SnO2–Sb2O3 nanoparticles were obtained by using polymeric precursor method. Powders were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential thermal analysis and thermogravimetric analysis (DTA/TGA).
Montenegro Hernandez, Alejandra +3 more
openaire +2 more sources
Advanced Healthcare Materials, EarlyView.Comparison of therapeutic and diagnostic applications of a surface‐emitting light source with multiwavelength emission characteristics. Abstract Conventional light‐emitting‐diode‐based light sources suffer from rigidity, localized heating, and poor adaptability to skin deformation, limiting their use in skin‐attached medical devices.
In Ho Kim +10 more
wiley +1 more source
Advanced Materials, EarlyView.Fluorene‐functionalized spiro‐phenothiazine (PTZ‐Fl) exhibits strong Li+ affinity and thermal stability, enabling a PCE of 25.75% in small‐area cells and 22.07% in 25 cm2 modules. Under ISOS‐L3 conditions, PTZ‐Flbased devices retain over 80% efficiency after 1000 hours, demonstrating superior stability and scalability compared to spiro‐OMeTAD for next ...
Javier Urieta‐Mora +17 more
wiley +1 more source
Opportunities of Semiconducting Oxide Nanostructures as Advanced Luminescent Materials in Photonics
Advanced Materials, EarlyView.The review discusses the challenges of wide and ultrawide bandgap semiconducting oxides as a suitable material platform for photonics. They offer great versatility in terms of tuning microstructure, native defects, doping, anisotropy, and micro‐ and nano‐structuring. The review focuses on their light emission, light‐confinement in optical cavities, and
Ana Cremades +7 more
wiley +1 more source
Advanced Materials, EarlyView.In this work, low bandgap (≈1.55 eV) semitransparent perovskite solar cells (ST‐PSCs) having thin (thickness < ≈100 nm) perovskite layers and transparent conductive oxide‐based rear electrodes are fabricated using vacuum‐deposition methods. Two different ST‐PSCs demonstrated a high light utilization efficiency value of 4.2 (PCE: 9.26% and AVT: 45.3 ...
Abhyuday Paliwal +9 more
wiley +1 more source
Advanced Materials, EarlyView.The transient interactions between TFSI− anions and a diluent within an anion‐dictated electrolyte are revealed, which can reduce interfacial reorganization energy, thereby accelerating ion kinetics and markedly facilitating sustainable anion storage in high‐voltage graphite cathodes for dual‐ion batteries at fast charge and wide temperature range ...
Sungho Kim +9 more
wiley +1 more source
Revue des Énergies Renouvelables, 2008 Le défi principal dans la réalisation des cellules solaires est l’augmentation du rendement de conversion sans surcoût additionnel dans le procédé de fabrication.
R. Tala-Ighil +4 more
doaj