Results 71 to 80 of about 35,670 (298)

Comparative study of techniques for measurement of linewidth and frequency noise of single-frequency lasers [PDF]

, 2022
Paper ATh2A.13Measuring the linewidth of single-frequency lasers is challenging, and great care must be taken to understand the capabilities and limitations of different measurement techniques to obtain consistent results.
Warden, M.S., Lagatsky, A.A., Karpushko, F.V., Bonner, G.M., Thomas, J.W., Bongs, K., Jones, B.E., Stothard, D.J.M., Hunter, C., Singh, Y., Jones, J.M., McKnight, L.J.   +11 more
core   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

A 606 W burst-mode picosecond Yb-doped all-fiber laser with an intra-burst repetition rate of 469 MHz

High Power Laser Science and Engineering
This paper introduces a novel fiber-based picosecond burst-mode laser system capable of operating at high power and high repetition rates. A pulse-circulating fiber ring was developed as a burst generator, achieving an intra-burst repetition rate of 469 ...
Xinyao Li, Haijuan Yu, Shuzhen Zou, Chaojian He, Chaoyu Ning, Wenjuan Wu, Xuechun Chen, Xuechun Lin   +7 more
doaj   +1 more source

Creating Ti–Fe α/β Alloys by Diffusion‐Driven Solid‐State Processing

Advanced Engineering Materials, EarlyView.
This study proposes making alloys containing fast diffusing elements that are difficult to produce by ingot metallurgy, by diffusion‐driven solid‐state HIP processing of elemental powders and low‐temperature homogenisation. Here, novel Fe‐Ti α–β alloys are formed having fine α–β lamellae, a small β prior grain size without significant intermetallics ...
Jiaqi Xu, Xun Zhang, Jack M. Donoghue, Albert D. Smith, Rahul Unnikrishnan, Rhys Thomas, Vahid Nekouie, Jie Luo, Dongchen Hu, Michael Preuss, Philip J. Withers   +10 more
wiley   +1 more source

One- and two-photon pumped organic semiconductor lasers [PDF]

, 2010
This thesis describes a number of studies on organic semiconductors focused around using them as gain media for lasers. The photophysical properties of organic semiconductors are studied using a wide range of experimental techniques, allowing the ...
Tsiminis, Georgios
core   +1 more source

High-Power, Wavelength-Locked 878.6 nm In-Band Pumped, Acoustic-Optically Q-Switched Nd:YVO₄ MOPA Laser With TEM₀₀ Mode

IEEE Photonics Journal, 2016
In this paper, a wavelength-locked 878.6-nm pumped acoustic-optically Q-switched Nd:YVO4 laser is presented. A master oscillator power amplifier configuration with two-stage amplifiers is employed to scale the output power.
Qiang Liu, Mingming Nie, Fuyuan Lu, Mali Gong   +3 more
doaj   +1 more source

Affecting the Properties of Copper–Graphene Electroconductive Composite by Severe Plastic Deformation

Advanced Engineering Materials, EarlyView.
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich, Lenka Kunčická, Pavel Czernek, Zifan Wang   +3 more
wiley   +1 more source

Is an Apple an Orange? A Large Language Model Benchmark for Candidate Term Extraction and Subclass Decisions Against Upper Ontologies in Engineering and Materials Science

Advanced Engineering Materials, EarlyView.
Building machine‐readable vocabularies for materials science is slow, expert‐driven work. This study benchmarks 13 large language models on two of its first steps: finding candidate terms in engineering articles and deciding where they belong in a class hierarchy.
Thomas Bjarsch, Maximilian Holland, Klaus Drechsler, Johannes Schilp   +3 more
wiley   +1 more source

Ultrashort-pulse generation from quantum-dot semiconductor diode lasers [PDF]

, 2008
In this thesis, novel regimes of mode locking in quantum dot semiconductor laser diodes have been investigated by exploiting the unique features offered by quantum dots.
Cataluna, Maria Ana
core