Results 71 to 80 of about 12,242 (259)
This study presents ultrathin, high‐capacity aluminum‐air batteries (AABs) for self‐sustaining, skin‐conformal electronics. By utilizing ambient moisture and oxygen alongside a LiCl‐based hygroscopic hydrogel electrolyte, the design significantly reduces battery thickness while preventing dehydration and Al self‐corrosion.
Jaeil Park +12 more
wiley +1 more source
SPRAY DEPOSITION FROM AN UNMANNED AERIAL VEHICLE ON A COFFEE CROP [PDF]
The use of unmanned aerial vehicles (UAVs) to apply pesticides has grown significantly, but technical data to support improvements in application efficiency are lacking, especially for perennial crops.
João P. A. R. da Cunha +4 more
doaj +1 more source
Matrix‐assisted laser desorption/ionization imaging‐based identification of reliable small molecule markers across heterogeneous glioblastoma cohorts is challenging with intensity‐only methods. We present spatially informed feature selection (SIFS), a spatially informed framework that prioritizes molecules consistently colocalizing with histopathology.
Shad A. Mohammed +15 more
wiley +1 more source
Single string cavitation and swirling flow in a nozzle and a hollow-cone spray
Single string cavitation (SC) and a swirling flow around it may occur in a fuel injector of diesel engines at the moment of low needle lift, if the tip of the needle valve is close to the nozzle entrance.
Dongping SHEN +3 more
doaj +1 more source
Process Optimization of Solution Blow Spinning for Poly (N‐Isopropylacrylamide) Fibers
Solution blow spinning has emerged as a safe and scalable technique for fabricating thermoresponsive PNIPAM fibers. The influence of key parameters on jet stability and fiber uniformity is determined through both rheological analysis and statistical process optimization. A Box–Behnken design reveals an optimized window for producing PNIPAM fibers below
Maryam Parastar +2 more
wiley +1 more source
Material Characterization of Lignin‐Filled Polypropylene Composites
Ground and spray‐dried lignin powders are compared as fillers for polypropylene composites. Differences in powder preparation methods are associated with differences in powder characteristics and composite behavior after melt compounding. Spray‐dried lignin produces smaller particles and fewer large agglomerates, while a 5 wt% lignin loading provides a
Sungjun Hwang +3 more
wiley +1 more source
This paper presents a detailed Computational Fluid Dynamics (CFD) analysis of nutrient spray flow characteristics from an aeroponic nozzle for enhancing plant nourishment in sustainable agriculture systems.
Aeswin Lawrance +2 more
doaj +1 more source
High‐entropy perovskite oxides enable tunable structures and properties through multi‐cation disorder and entropy stabilization. This review summarizes advances in synthesis, structural and defect engineering, and their applications in OER/ORR, CO2RR, and electrochemical energy storage, highlighting in situ characterization and modeling that clarify ...
Obeylaw Moyo +8 more
wiley +1 more source
The Effect of Water Management and Cell Compression in Bipolar Membrane CO2 Electrolysis to CO
In‐operando neutron imaging uncovers water management challenges in bipolar membrane CO2 electrolysis: Internal water generation floods the cathode, while compression dictates membrane and gas diffusion electrode integrity. Strategic adjustments are applied in this work: dry gas feed and mechanical support of the gas diffusion electrode enable stable ...
Frederik Brendel +7 more
wiley +1 more source
Effects of Nozzle Arrangement Strategies on Spray Uniformity in Soybean–Maize Intercropping
Soybean–maize intercropping involves the simultaneous planting of maize and soybean. Compound planting sprayers are equipped with a dual-spraying system, particularly for herbicide application, where isolation between crops is essential.
Wei Zhong +7 more
doaj +1 more source

